AVR 645

AVR 645

Audio/Video Receiver With Dolby Digital, DTS & HDMI 1.1 Switching (90 watts x 2 | 75 watts x 7)

Vendido desde 2006 hasta 2007

Producto sucesor: AVR 3550HD
Hecho en: China

Documentos y descargas

Especificaciones del producto

Power Requirements
AC 120V/60Hz
Power Consumption
120W @ Power On, idle; 1272W @ rated power output (7 channels driven)
Digital Inputs (coaxial/optical)
3/3 on Rear; 1 (switchable to output)/1 on front; 1 USB on rear
Analog Inputs
1 A/V on front panel (switchable to output)
Analog Inputs
2 audio- only
Analog Inputs
4 A/V on rear panel
Analog Inputs
6-/8-channel input
Analog Inputs
The Bridge Digital Media Player
Analog Inputs
tuner
On-Screen Display
Yes, including component video
Multizone Capability
Audio; A-BUS Ready; RS-232 serial control port; surround back channels assignable to remote zone; ZR 10 remote
Auto Setup
EzSet/EQ room equalization
Remote Control
Backlit, eight-device, programmable learning remote (2-line LCD display)
Shipping Weight (System, Accessories, Packing)
47 lb (21.4kg)
MSRP U.S.
$1499.95 each
# of Amplifier Channels
7
Continuous Average Power (FTC) per Channel (stereo mode)
90 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms
Front L & R Channels
75 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Center Channel
75 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Surround Channels (L & R Side, L & R Back)
75 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Input Level/Impedance
200mV/47k ohms - Linear (High-Level)
Signal-to-Noise Ratio
100dB (IHF-A)
Surround System Adjacent Channel Separation:
Dolby Pro Logic I and II
40dB
Dolby Digital
55dB
DTS
55dB
Frequency Response
10Hz – 130kHz (+0/-3dB @ 1 watt)
Transient Intermodulation Distortion (TIM)
Unmeasurable
Slew Rate
40V/µsec
Width
17.3 inch (440mm)
Height
6.5 inch (165mm)
Depth
17.1 inch (435mm)
Weight
41 lb (18.6kg)
Dimensions:
Carton Dimensions
20.1 inch x 10 inch x 22.2 inch (510mm x 254mm x 565mm)
Television Format
NTSC
Input Level/Impedance
1Vp-p/75 ohms
Output Level/Impedance
1V/75 ohms
Video Frequency Response:
Composite and S-Video
10Hz – 8MHz (–3dB)
Component Video
10Hz – 100MHz (–3dB)
HDMI
Version 1.1 with audio processing
Frequency Range
AM... 520–1720kHz
Frequency Range
FM... 87.5 – 108.0MHz
Signal-to-Noise Ratio
AM... 45dB
Usable Sensitivity
FM... IHF 1.3µV/13.2dBf
Signal-to-Noise Ratio
FM... Mono/Stereo 70dB/68dB
Usable Sensitivity
AM... Loop 500µV
Distortion
AM... 1kHz, 50% Mod 0.8%
Distortion
FM... Mono/Stereo 0.2%/0.3%
Selectivity
AM... ± 10kHz, 30dB
Stereo Separation
FM... 40dB @ 1kHz
Selectivity
FM... ± 400kHz, 70dB
Image Rejection
FM... 80dB
IF Rejection
FM... 90dB
Amplifier Power (RMS)
75 x 7 @ 8 ohms, (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
High Instantaneous Current Capability (HCC)
± 50 Amps

Versatility at its best! The AVR 645 not only switches two HDMI; 1.1 sources, it is able to decode Dolby Digital, DTS and PCM audio streams from the HDMI inputs. Add USB audio, iPod connectivity and XM-Ready capability to our EzSet/EQ system and high-current amplifier, and the AVR 645 performs with ease. Equally impressive on the video side is transcoding so that all analog video inputs may be viewed via component outputs, and A/V Sync Delay, which reconnects the timing of sound and images. There is no better combination of sound and image anywhere.

¿No encuentras lo que buscas?

Llámanos

Llámanos

Llámanos a este número: 55-5328-1022

Lunes - Viernes: 09:00 AM -06:00 PM (Hora Centro)

Envíanos un correo electrónico

Envíanos un correo electrónico

los 365 días del año.

Te responderemos en el plazo de un día laborable.

Envíanos un correo electrónico