Switch device ON.
Press and hold VOLUME+ and PLAY/PAUSE buttons until all lamps light up.
Device is now reset.

Download the HK Connect app to your mobile device. Make sure that the Onyx Studio 4 speaker is connected successfully to your mobile device. The HK Connect app should recognize the Onyx Studio 4 within the first few seconds. Once inside the app you can activate the voice assistant and connect to other Connect+ Harman Kardon devices.

At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.

In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.

We offer a 30 day free return period. To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.

Resetting the Go + Play 3 to Factory Settings:

In power ON mode, press and hold the "Volume +" and "Bluetooth" buttons at the same time for more than 10 seconds.

- The Go + Play 3 will power off and back on and is now reset

Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.

By pressing and holding the "Volume+" and "Handsfree" ( phone ) button together for 5 seconds. The Harman Kardon Aura Studio will power off, and is now reset back to factory defaults.

Press and hold the bluetooth button for 2-3 seconds. The bluetooth button is located on the bottom RIGHT ear cup. If this is your first time turning on the headphones, it should immediately begin to search for a device to connect to. You will see the blue LED light flash on the bluetooth symbol as it begins to search for the device. Make sure the bluetooth setting is on and in search mode on your device. The Soho Wireless should appear on your discoverable devices within 3-5 seconds. To power off, press and hold the bluetooth button until you hear the audio music prompt indicating that it has powered down.

Make sure that the unit you are attempting to connect to is in pairing mode under Bluetooth Settings. Press the power button located on far right outer rim of the speaker. If this is the first time connecting the unit, it will immediately go into pairing mode. HK Onyx 4 Studio should show up on your discoverable devices within 3-5 seconds. Once you choose the HK Onyx Studio 4 on your device, you will be connected and ready to experience that superior Harman Kardon sound.

1. Place the 3770 in Bluetooth input mode with the BT button on the front panel or the remote. 2. Do a BT search on the phone, until you find HK3770. Then pair with it. 3. Now you can select the HK3770 as audio source on your phone, depending on the phone. On some phones, you can simply begin to play music after performing the pairing, and the HK3770 will play, if it is in Bluetooth input mode, shown on the front panel display. 4. You can control play/pause etc. from either your phone or from the HK3770 remote control. If you want to use the HK3770 remote, you must first press the STEREO Button on the remote control in order to activate the correct remote codes. Now a press on the PAUSE Button on the HK3770 remote will pause the music by placing your phone on pause, and you can restart play by pressing the PLAY Button. 5. To pair another source to HK3770, first deactivate BT on the source presently paired to release new pairing.

You can download a copy of your invoice on our website. Go to "Order Status" under "Order Support" in the menu bar. To access your order details and download your invoice, you will need the following details:

 

• Order number
• Surname
• Billing postal code

 

Once directed to your order details, there is an option to download your invoice.

The details on your invoice is a direct reflection of your order details. We are unable to amend the details on your invoice.

We recommend starting playback on the Omni+ speaker first, and then linking the 1st generation Omni speakers. Omni+ is more powerful and can provide more stability when restreaming to other speakers.

You need to download the HK Alexa setup app from either Google Play Store or Apple App Store, then follow the procedure written in the app.

With the SB35 in standby, press and hold Volume plus and Volume Minus for more than three seconds. The software version is now shown on the front panel display, under the fabric grille. It is the first figure that is the software. More info is shown, but is not relevant for user.

Plug in via USB charging port behind the cap on the RIGHT side of your neckband just below the volume controls. When the light is on, your neckband turns green. (Press the plus and minus on the volume control to get the battery status)

You can change the volume on the Harman Kardon Aura Studio 2 by either using the volume control ( indicated with the + and - ) on the front of the Aura Studio 2. Alternatively, when connected by Bluetooth from a mobile device, you can change the volume from the mobile device. There are 32 steps in the volume

The two subwoofer outputs are parallel, meaning that when changing subwoofer settings in the setup menu, both outputs will be adjusted. Establish the 7.2 system simply by adding a second subwoofer to an existing 7.1 system, connecting it to sub output 2.

Vi measures heart rate using an optical heart rate sensor in the left earbud. The sensor emits light in a specific wavelength to the tissue of the tragus in the ear, and the reflective light is captured by the receiver of the sensor, that is processed by a proprietary algorithm to capture the heart rate. If you need assistance getting an accurate and consistent heart rate, check out this tutorial video to find the correct fit.

Each speaker, adaptor and phone/tablet connects to your home Wi-Fi network, just like any other Wi-Fi produce you own. You can then stream any music from your phone/tablet to any Omni speaker or Adapt over your home network

With no signal, the BDS will turn itself off after the number of minutes you have previously set. When connected with optical cable to an external source, and with signal present, it will not turn off, even if the Auto Turn Off is on.

You can send any 4k video signal into the HDMI inputs of your AVR, and it will be sent to your TV screen from the HDMI output, either in 4k or 1080p. Sometimes it may be necessary to switch off the TV set, then switch it on again, to activate a new "handshake" between the devices, in order to open for the 4k signal, if normal HD 1080p signal was the last signal used. Please note that not all 4k signals can be viewed. Many streamed videos from Youtube will work, as will any 4k material that you have recorded yourself, and many TV boxes will work also. However, HDCP 2.2 protected material will not be shown in 4k, but will be converted to full HD 1080p signals, because these AVRs do not support HDCP 2.2 digital copy protection. HDR is not supported.

Please refer to the owner's manual for AVR 151 or 151S. The procedure is explained there. The remote control contains a number of pre-programmed command sets that can be activated to control TV sets, disc players and other devices of various brands.

The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.

Download and connect the Onyx Studio 9 with the Harman Kardon One app. Select the product in the app and go to [Product information] and then select [Product Software]. If a new update is available, you can select [Update].

To choose a wireless network for your BDS system, please do the following. 1: Select Choose a network from the Setup Wi-Fi list. 2: Follow the instructions on the screen to select your wireless home network and enter your security password, if applicable.

By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.

With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.

On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.

The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.

There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.

Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.

To prevent other people from changing the source on your BDS through Bluetooth, you can disable the “Automatic Playback” function in the System Settings of the BDS ( 280, 580, 280S and 580S ). This does not prevent others from connecting to one of the two Bluetooth receivers in the BDS units, but it prevents other people from “interrupting” your playback source. This is where the change is done: Settings – System Settings Automatic Playback ( Enable/Disable ) Enabled: People can connect to your BDS and start playing music/audio. Your BDS will automatically change source ( or switch on, when BDS is in Standby mode ) from any source. Disabled: People can connect to your BDS, but the BDS will not automatically change source, or go out of Standby mode when a music/audio signal is sent through Bluetooth.

We have some suggestions if you want to enjoy the best performance from your Bluetooth devices. 1. Please note that if you have a large number of Apps open in your smartphone or tablet, this may block or overtax its processor. Dropouts may result. Try to close all or most active apps. This should solve the problem. 2. Bluetooth signals from smartphones and tablets are not very strong. Make sure that the signal does not have to pass through doors, walls etc. Always maintain a clear line of sight between transmitter and receiver. 3. Do not carry your smartphone in your pocket, if you have dropouts. Your body can act as a screen, reducing the strength of the Bluetooth signal. Put the phone on a table or other surface. 4. Do not walk around while listening. If the transmitter and the receiver are moved in relation to each other, dropouts occur more frequently. 5. Under normal circumstances, you can expect a range of 5 meters with no problems, if you follow the above advice. In some instances range is longer, but we cannot promise this.

That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".

Once the speaker/soundbar is connected to the network, software updates will automatically be sent to the product through Wi-Fi or the internet, if available

For Citation ONE, Citation 100, Citation Sub and Citation Surround, Press and hold the RESET button on the speaker for 5 seconds. For Citation 300, Citation 500, Citation Bar and Citation Tower, Press and hold the RESET button on the speaker for 5 seconds, or select the Factory Reset option in the touch screen settings menu.

Press the Bluetooth source button on your BDS remote. In the right top corner of your TV screen, there should be a button called "Pair". Jump to the "Pair button" to perform pairing by using the arrow keys on your remote control. Click OK while being on the pair button. Once pressed, a pop-up screen will appear, this indicates pairing mode is active for 3 minutes. Go to Bluetooth settings on your mobile device, find the BDS in the list and connect. If you want to pair a second device, please repeat the procedure to activate pairing mode.

You can delete specific voice recordings associated with your account by going to History in Settings in the Alexa App, drilling down for a specific entry, and then tapping the delete button. Or, you can delete all voice recordings associated with your account for your Harman Kardon Allure speaker, by selecting the applicable product at the Manage Your Content and Devices page at www.amazon.com/mycd. and deleting voice recordings. However, this may degrade your Alexa experience.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

HDMI Output

Both Enchant 800 and Enchant 1300 support these:

• HDMI 2.0b compliance
• HDCP 2.2 compliance (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
• CEC features (Scroll to see support)

HDMI Input

Enchant features only 1 x HDMI input, and Enchant has 3 x HDMI inputs and support this:

• HDMI 2.0b.
• HDCP 2.2 for all HDMI input connections (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
• 4K Pass-through.

CEC Support

CEC support only available through your HDMI connection and we are always using standard protocol for our products.
We support these:

• System Standby: When you press the "Power off" button on your TV remote, the Enchant soundbar will go into Standby mode as well.
• ARC or called Audio Return Channel: If you would have a TV BOX connected directly to your TV and using ARC from TV to Enchant soundbar, then all sound will be transferred through ARC connection.
  • In case you are not using the HDMI ARC connection then sound coming from the TV show will not be transferred to the Enchant soundbar.
• System Audio Control: Using your TV remote to turn up or lower the volume will be synchronized with the Enchant soundbar.

Bigger model is the Enchant 1300 and smaller model is the Enchant 800.

The Citation Amp works with Chromecast built-in (audio only), and also works with Hey Google products. For example, you can use voice commands to tell your other Google speakers to play music on Citation Amp.

To reset the device to its factory settings: 
Power on the speaker. While on, press and hold the power button down for 15-20 seconds until the speaker turns off.

Now that the speaker has been reset, make sure to remove it from your BT settings if it was once paired to other devices as the BT memory has been reset as well. Once you turn the speaker on again, it should automatically enter into pairing mode with a flashing LED. It should pop up on your discoverable devices under your BT settings and connect within a few seconds. 

ENCHANT SUB

Software Update Release Notes

------------------------------------------------------------------------

Version:  24.51.11.75.00

Release Date: January 20th, 2025

Release Media: OTA (over the air) Automatic Update through HK One App

 

What’s New

1. Improved software performance

ENCHANT 900

Software Update Release Notes

------------------------------------------------------------------------

Version:  24.50.65.90.00

Release Date: January 20th, 2025

Release Media: OTA (over the air) Automatic Update through HK One App

 

What’s New

1. Increase EQ to 7 bands
2. Improved software performance

ENCHANT 1100

Software Update Release Notes

------------------------------------------------------------------------

Version:  24.50.65.90.00

Release Date: January 20th, 2025

Release Media: OTA (over the air) Automatic Update through HK One App

 

What’s New

1. Increase EQ to 7 bands
2. Improved software performance

It's normal that music will be interrupted for one or two seconds when entering Wireless Dual Sound mode. The two compatible speakers are synchronizing with each other during this connection process. Once they are in sync you will not experience any further interruption.

The Onyx Studio 7 features Dual Wireless Sound which allows you to connect two Onyx Studio 7 speakers together for a more powerful listening experience. Please note: You cannot connect the Onyx Studio 7 to other Onyx Studio speakers such as the Onyx Studio 6 and 5. 

Yes, a phone with GPS capabilities is needed so that the Vi Fitness app can start and stop workouts, track biometrics, measure and store data, track features like elevation and location, and play music during training. We support iOS (9+) and Android OS (Lollipop +) devices however we recommend having the latest OS on any device for the best Vi experience.

Every home is different, so it is difficult to provide a universal guide that suits it all. What you can do is check the number of available access points in your home by performing a Wi-Fi network scan using a mobile device. Then select the Wi-Fi channel that isn't as busy as the rest. Also, check how much noise each speaker has using the Harman Kardon Controller app. Simply go into the settings menu and select "Send us feedback" to see the results, signals between -40 dB and -62 dB are considered good.

Yes, this headphone features a one button microphone that gives you the ability to pause/play, skip tracks, and answer/hang up phone calls.

No, the HDMI connection is used for audio return channel only, there is no on-screen display function to show settings on the TV screen.

Yes, press and hold the Surround button on the OMNI BAR+ until it starts to blink amber. You are now in pairing mode. Press Volume+ on your OMNI BAR+, then press Volume+ on your remote control. The surround button will quickly flash white, to indicate it has learned Volume+. Repeat for Volume-, and Mute, and then hold down the Surround button to exit remote control learning.

No, since the OMNI BAR+ does not have any HDMI input connections, it is only your source, connected to the TV, (and of course your TV) that need to be 4K compatible.

No, this feature is not supported in our Harman Kardon Allure speaker. This might change with future updates. You can write text messages to your Amazon friends via the Alexa app.

Harman Kardon Allure/portable will only work in selected countries such as United States, Germany, United Kingdom and soon France. To use the Allure on your network requires two different apps. 1. HK Alexa setup - To connect it to your Wi-Fi network (Only available in the countries above) 2. Amazon Alexa app - To control Alexa and add streaming services to your Allure speaker. However, in some countries, French, German or English is spoken, but you still cannot use the Allure, because the Amazon Alexa app cannot be downloaded. This is a decision made by Amazon. The Alexa app is only available in some countries, and this is not only dependent on language. Therefore, if you plan on buying an Allure speaker, and have it shipped to a country outside the selected regions, you will not be able to use it on Wi-Fi, and Alexa voice commands will not work. Only Amazon knows if and when they will extend the app availability to more countries.

The Harman/Kardon SB20 is an easy connectable soundbar for your TV. It only has outputs for TV connection, and we advise to connect all other HDMI sources to your TV instead.

No, the Citation speaker does not store any conversations, it listens only for a few seconds and then deletes the file. Only when using "OK, Google" or "Hey, Google" will it start recording your question in order for Google Assistant to fulfill your request. You can always delete all your recordings via "My activity" settings under your Google Account.

The product does not have a built-in voice assistant. However, the product works with other voice-enabled products supporting Google Voice Assistant or Amazon Alexa.

Yes, The Harman Kardon Aura Studio supports Social mode. With this feature, you can connect up to 3 mobile devices simultaneously by Bluetooth. The last device to start playback will take over.