How To
How To
503 results
-
With the SB35 in standby, press and hold Volume plus and Volume Minus for more than three seconds. The software version is now shown on the front panel display, under the fabric grille. It is the first figure that is the software. More info is shown, but is not relevant for user.Was this helpful? Thank you for your feedback!
-
You need to download the HK Alexa setup app from either Google Play Store or Apple App Store, then follow the procedure written in the app.Was this helpful? Thank you for your feedback!
-
We recommend starting playback on the Omni+ speaker first, and then linking the 1st generation Omni speakers. Omni+ is more powerful and can provide more stability when restreaming to other speakers.Was this helpful? Thank you for your feedback!
-
The HD 3700 will list each folder or directory together. Folders that are found in different directories can be easily navigated to using the FOLDER +/- button. Simply press the FOLDER +/- button to skip between different directories.Was this helpful? Thank you for your feedback!
-
1. Place the 3770 in Bluetooth input mode with the BT button on the front panel or the remote. 2. Do a BT search on the phone, until you find HK3770. Then pair with it. 3. Now you can select the HK3770 as audio source on your phone, depending on the phone. On some phones, you can simply begin to play music after performing the pairing, and the HK3770 will play, if it is in Bluetooth input mode, shown on the front panel display. 4. You can control play/pause etc. from either your phone or from the HK3770 remote control. If you want to use the HK3770 remote, you must first press the STEREO Button on the remote control in order to activate the correct remote codes. Now a press on the PAUSE Button on the HK3770 remote will pause the music by placing your phone on pause, and you can restart play by pressing the PLAY Button. 5. To pair another source to HK3770, first deactivate BT on the source presently paired to release new pairing.Was this helpful? Thank you for your feedback!
-
Make sure that the unit you are attempting to connect to is in pairing mode under Bluetooth Settings. Press the power button located on far right outer rim of the speaker. If this is the first time connecting the unit, it will immediately go into pairing mode. HK Onyx 4 Studio should show up on your discoverable devices within 3-5 seconds. Once you choose the HK Onyx Studio 4 on your device, you will be connected and ready to experience that superior Harman Kardon sound.Was this helpful? Thank you for your feedback!
-
Press and hold the bluetooth button for 2-3 seconds. The bluetooth button is located on the bottom RIGHT ear cup. If this is your first time turning on the headphones, it should immediately begin to search for a device to connect to. You will see the blue LED light flash on the bluetooth symbol as it begins to search for the device. Make sure the bluetooth setting is on and in search mode on your device. The Soho Wireless should appear on your discoverable devices within 3-5 seconds. To power off, press and hold the bluetooth button until you hear the audio music prompt indicating that it has powered down.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Handsfree" ( phone ) button together for 5 seconds. The Harman Kardon Aura Studio will power off, and is now reset back to factory defaults.Was this helpful? Thank you for your feedback!
-
Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.Was this helpful? Thank you for your feedback!
-
In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.Was this helpful? Thank you for your feedback!
-
At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.Was this helpful? Thank you for your feedback!
-
Press and hold the power on/off symbol/button for 3 seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call us
Talk to a product expert
Call us now at:
(800) 422-8027
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)
Chat with us
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)