AVR 745
Audio/Video Receiver With Dolby Digital, DTS & HDMI 1.1 Switching (100 watts x 2 | 85 watts x 7)
Sold from 2006 until 2008
Predecessor Product: | AVR 7300 |
---|---|
Successor Product: | AVR 7550HD |
Made in: | China |
Documents & Downloads
Product Specifications
- Power Requirements
- 120V AC/60Hz
- Power Consumption
- 8.9W Standby 130W Idle, 1,480W Max. (7 channels driven)
- Digital Inputs (coaxial/optical)
- 3/3 on rear; 1 (switchable to output)/1 on front
- Analog Inputs
- 1 A/V on front panel (switchable to output)
- Analog Inputs
- 2 audio-only
- Analog Inputs
- 5 A/V on rear panel
- Analog Inputs
- 6-/8-channel input
- Analog Inputs
- tuner
- On-Screen Display
- Yes, with component video
- Multizone Capability
- Audio and video; A-BUSREADY; RS-232 serial control port; surround back channels assignable to remote zone; Zone II remote
- Auto Setup
- EzSet/EQ II room equalization
- Remote Control
- TC 30 activity-based remote control with color LCD screen
- Shipping Weight (System, Accessories, Packing)
- 52 lb (23.6kg)
- MSRP U.S.
- $3499.95 each
- # of Amplifier Channels
- 7
- Continuous Average Power (FTC) per Channel (stereo mode)
- 100 Watts per channel @ <0.07% THD, 20Hz – 20kHz, both channels driven into 8 ohms
- Front L & R Channels
- 85 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Center Channel
- 85 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Surround Channels (L & R Side, L & R Back)
- 85 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Input Level/Impedance
- 200mV/47k ohms - Linear (High-Level)
- Signal-to-Noise Ratio
- 100dB (IHF-A)
- Frequency Response
- 10Hz – 130kHz (+0/-3dB @ 1 watt)
- Surround System Adjacent Channel Separation:
- Dolby Pro Logic I/II/IIx
- 40dB
- Dolby Digital
- 55dB
- DTS
- 55dB
- Transient Intermodulation Distortion (TIM)
- Unmeasurable
- Slew Rate
- 40V/µSec
- Width
- 17-5/16 inch (440mm)
- Height
- 6-1/2 inch (165mm)
- Depth
- 17-1/8 inch (435mm)
- Weight
- 48 lb (21.8kg)
- Dimensions:
- Carton Dimensions (H x W x D)
- 10-3/4 inch x 20-1/2 inch x 22-3/4 inch (273mm x 521mm x 578mm)
- Television Format
- NTSC
- Input Level/Impedance
- 1Vp-p/75 ohms
- Output Level/Impedance
- 1V/75 ohms
- Composite and S-Video
- 10Hz – 8MHz (–3dB)
- Component Video
- 10Hz – 100MHz (–3dB)
- Frequency Range
- AM... 520 – 1710kHz
- Frequency Range
- FM... 87.5 – 108.0MHz
- Signal-to-Noise Ratio
- AM... 45dB
- Usable Sensitivity
- FM... IHF 1.3µV/13.2dBf
- Signal-to-Noise Ratio
- FM... Mono/Stereo 70dB/68dB
- Usable Sensitivity
- AM... Loop 500µV
- Distortion
- AM... 1kHz, 50% Mod. 0.8%
- Distortion
- FM... Mono/Stereo 0.2%/0.3%
- Selectivity
- AM... ± 10kHz, 30dB
- Stereo Separation
- FM... 40dB @ 1kHz
- Selectivity
- FM... ± 400kHz, 70dB
- Image Rejection
- FM... 80dB
- IF Rejection
- FM... 90dB
- Amplifier Power (RMS)
- 85 x 7 @ 8 ohms (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
- High Instantaneous Current Capability (HCC)
- ± 60 Amps
Digital audio meets digital video. The AVR 745's DCDi by Faroudja video processing upscales all incoming video to 720p or 1080i. Two HDMI; 1.1 inputs are available to decode audio for true single-wire connectivity. Digital audio extras include XM Ready capability, iPod playback through The Bridge docking station, and USB playback from compatible computers. (Optional XM antenna module and subscription to XM service required. Hardware and service sold separately. XM service is not available in Alaska or Hawaii.) Our EzSet/EQ; II system, 7.2-channel output, TC 30 remote and more make this the most flexible AVR we've ever produced.
FAQs & How-Tos
-
This receiver has a feature called "A/V Sync Delay" that allows you to manually set dissimilar video and audio synchronization that may occur with certain types of Plasma and HDTV's. The instruction for this setting can be found in your owner's manual in the section "Delay Adjustments" or "Delay Settings".Was this helpful? Thank you for your feedback!
-
Please check the picture settings on your cable box, particularly the aspect ratio settings, which will vary depending on the brand and model of your cable box and on your local cable provider. You may wish to consult with your cable provider for more information on how to adjust the cable box's settings. Some settings, such as a setting to force an analog channel's native 4:3 aspect ratio to 16:9 widescreen to fit your display, may interfere with the cable system's copy-protection feature and cause distortion.Was this helpful? Thank you for your feedback!
-
The remote is only capable of operating one device at a time (unless you have programmed advanced functions such as Volume, Channel or Transport control Punch-Through). When you press the Source Selector to operate your other product, such as the DVD player, the remote cannot control any other product, including the AVR, until you press the AVR Button again. To avoid your problem in the future, always press the AVR Button or appropriate Source Selector before you enter any command.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(800) 422-8027
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)
Chat with Us
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)