AVR 645
Audio/Video Receiver With Dolby Digital, DTS & HDMI 1.1 Switching (90 watts x 2 | 75 watts x 7)
Sold from 2006 until 2007
Successor Product: | AVR 3550HD |
---|---|
Made in: | China |
Documents & Downloads
Product Specifications
- Power Requirements
- AC 120V/60Hz
- Power Consumption
- 120W @ Power On, idle; 1272W @ rated power output (7 channels driven)
- Digital Inputs (coaxial/optical)
- 3/3 on Rear; 1 (switchable to output)/1 on front; 1 USB on rear
- Analog Inputs
- 1 A/V on front panel (switchable to output)
- Analog Inputs
- 2 audio- only
- Analog Inputs
- 4 A/V on rear panel
- Analog Inputs
- 6-/8-channel input
- Analog Inputs
- The Bridge Digital Media Player
- Analog Inputs
- tuner
- On-Screen Display
- Yes, including component video
- Multizone Capability
- Audio; A-BUS Ready; RS-232 serial control port; surround back channels assignable to remote zone; ZR 10 remote
- Auto Setup
- EzSet/EQ room equalization
- Remote Control
- Backlit, eight-device, programmable learning remote (2-line LCD display)
- Shipping Weight (System, Accessories, Packing)
- 47 lb (21.4kg)
- MSRP U.S.
- $1499.95 each
- # of Amplifier Channels
- 7
- Continuous Average Power (FTC) per Channel (stereo mode)
- 90 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms
- Front L & R Channels
- 75 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Center Channel
- 75 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Surround Channels (L & R Side, L & R Back)
- 75 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Input Level/Impedance
- 200mV/47k ohms - Linear (High-Level)
- Signal-to-Noise Ratio
- 100dB (IHF-A)
- Surround System Adjacent Channel Separation:
- Dolby Pro Logic I and II
- 40dB
- Dolby Digital
- 55dB
- DTS
- 55dB
- Frequency Response
- 10Hz – 130kHz (+0/-3dB @ 1 watt)
- Transient Intermodulation Distortion (TIM)
- Unmeasurable
- Slew Rate
- 40V/µsec
- Width
- 17.3 inch (440mm)
- Height
- 6.5 inch (165mm)
- Depth
- 17.1 inch (435mm)
- Weight
- 41 lb (18.6kg)
- Dimensions:
- Carton Dimensions
- 20.1 inch x 10 inch x 22.2 inch (510mm x 254mm x 565mm)
- Television Format
- NTSC
- Input Level/Impedance
- 1Vp-p/75 ohms
- Output Level/Impedance
- 1V/75 ohms
- Video Frequency Response:
- Composite and S-Video
- 10Hz – 8MHz (–3dB)
- Component Video
- 10Hz – 100MHz (–3dB)
- HDMI
- Version 1.1 with audio processing
- Frequency Range
- AM... 520–1720kHz
- Frequency Range
- FM... 87.5 – 108.0MHz
- Signal-to-Noise Ratio
- AM... 45dB
- Usable Sensitivity
- FM... IHF 1.3µV/13.2dBf
- Signal-to-Noise Ratio
- FM... Mono/Stereo 70dB/68dB
- Usable Sensitivity
- AM... Loop 500µV
- Distortion
- AM... 1kHz, 50% Mod 0.8%
- Distortion
- FM... Mono/Stereo 0.2%/0.3%
- Selectivity
- AM... ± 10kHz, 30dB
- Stereo Separation
- FM... 40dB @ 1kHz
- Selectivity
- FM... ± 400kHz, 70dB
- Image Rejection
- FM... 80dB
- IF Rejection
- FM... 90dB
- Amplifier Power (RMS)
- 75 x 7 @ 8 ohms, (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
- High Instantaneous Current Capability (HCC)
- ± 50 Amps
Versatility at its best! The AVR 645 not only switches two HDMI; 1.1 sources, it is able to decode Dolby Digital, DTS and PCM audio streams from the HDMI inputs. Add USB audio, iPod connectivity and XM-Ready capability to our EzSet/EQ system and high-current amplifier, and the AVR 645 performs with ease. Equally impressive on the video side is transcoding so that all analog video inputs may be viewed via component outputs, and A/V Sync Delay, which reconnects the timing of sound and images. There is no better combination of sound and image anywhere.
FAQs & How-Tos
-
This receiver has a feature called "A/V Sync Delay" that allows you to manually set dissimilar video and audio synchronization that may occur with certain types of Plasma and HDTV's. The instruction for this setting can be found in your owner's manual in the section "Delay Adjustments" or "Delay Settings".Was this helpful? Thank you for your feedback!
-
Please check the picture settings on your cable box, particularly the aspect ratio settings, which will vary depending on the brand and model of your cable box and on your local cable provider. You may wish to consult with your cable provider for more information on how to adjust the cable box's settings. Some settings, such as a setting to force an analog channel's native 4:3 aspect ratio to 16:9 widescreen to fit your display, may interfere with the cable system's copy-protection feature and cause distortion.Was this helpful? Thank you for your feedback!
-
The remote is only capable of operating one device at a time (unless you have programmed advanced functions such as Volume, Channel or Transport control Punch-Through). When you press the Source Selector to operate your other product, such as the DVD player, the remote cannot control any other product, including the AVR, until you press the AVR Button again. To avoid your problem in the future, always press the AVR Button or appropriate Source Selector before you enter any command.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Talk to a product expert
Call us now at:
(800) 422-8027
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)
Chat with us
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)