Enchant Subwoofer
10” Wireless Subwoofer
Getting started with your Enchant Subwoofer
Register your product
Do you own this product? Register it here! And claim your warranty or service easily
Register nowDocuments & Downloads
Product Specifications
- Maximum Audio Power
- 400W
- RMS Power
- 200W
- Standby Power Consumption
- <2W
- Woofer Size
- 1 x 10" (254mm)
- Max SPL
- 83dB SPL/ 1W
- 2.4G Wireless Frequency Range
- 2403.35MHz - 2477.35MHz
- Note
- The subwoofer features standby mode. If the subwoofer is successfully connected to the soundbar, then it will enter/exit standby mode with the soundbar.
- Frequency Response
- 40Hz-160Hz
- Operating temperature
- 0°C - 45°C
- Dimensions (W x H x D)
- 11.7” x 15.7” x 11.7” (296mm x 400mm x 296mm)
Wireless. Powerful. Beautiful.
The Harman Kardon Enchant Subwoofer adds superior bass to the Enchant 1300 or 800 soundbars. Beautifully styled and featuring a 10” woofer, the Enchant Subwoofer’s wireless design easily enables an infinite number of placement options throughout your home theater. The state-of-the-art design delivers thunderous low tones that make your entertainment more exciting.
FAQs & How-Tos
-
How to pair an Enchant Subwoofer with your Enchant bar
- Go to the back of your Enchant soundbar (800 or 1300)
- Press the "Subwoofer pairing" button for 2 seconds.
- In front of your Enchant display, it will say "Subwoofer pairing"
- Go to the back of your Enchant subwoofer.
- Press the "Subwoofer pairing" button.
- The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.
You now have more bass performance and can enjoy deeper richer sound!Was this helpful? Thank you for your feedback! -
If you have a mesh network (more commonly seen in Eero Mesh networks), it is possible that you may experience your satellite speakers or subwoofer intermittently disconnecting from the soundbar. This is similar to normal interference that occurs with products on a similar wireless frequency. The special thing about Eero mesh networks is that they do not allow you to move a device to the 5Ghz or 2.4Ghz band. The system will automatically decide which devices should be on which band and will move them accordingly (switching whenever needed). Some of our soundbars run on a 5Ghz frequency which is where the interference can occur. Since we cannot change the signal in which they operate and we cannot change the band they are connected to via their Eero mesh network, there are a few things you can do to try and stop this from occurring.
- Move the mesh nodes far away from the soundbar
- Use the 2.4Ghz band instead of the 5Ghz band (if your mesh system allows this)
- Ensure to enable/utilize the MU-MIMO setting (not applicable to all mesh systems). Please refer to your router's website to see if MU-MIMO is being utilized by default.
What is MU-MIMO?
MU-MIMO stands for Multi-User, Multi-Input, Multi-Output. This allows for the router to send a signal to multiple devices at one time vs. the previous version in which the router would be able to connect to multiple devices, but only send the signal to one device at a time.
NOTE: You may notice that when the soundbar is turned on, there may be a dip in the immediate internet speed, but it will go back to normal within less than a minute.
Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Talk to a product expert
Call us now at:
(800) 422-8027
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)
Chat with us
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)