How To
How To
369 results
-
This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.Was this helpful? Thank you for your feedback!
-
Even though the Google Assistant is not built-in, Harman Kardon Radiance 2400 is compatible with a voice-assistant speaker, like the Harman Kardon Citation Series.Was this helpful? Thank you for your feedback!
-
You can use a 3.5 mini-jack cable to connect the Citation Amp (TRIGGER OUT 12V) with your subwoofer or other equipment to have them power on when the Citation Amp wakes from standby.
When the Citation Amp is ON, there will be output 12V DC signal, and when the Citation Amp is OFF mode, there is no output (0V DC).Was this helpful? Thank you for your feedback! -
The Citation Amp can work with 4 ohm speakers and is rated at 200-watts per channel. Do not connect speakers less than 4 ohm! Was this helpful? Thank you for your feedback! -
This receiver has a feature called "A/V Sync Delay" that allows you to manually set dissimilar video and audio synchronization that may occur with certain types of Plasma and HDTV's. The instruction for this setting can be found in your owner's manual in the section "Delay Adjustments" or "Delay Settings".Was this helpful? Thank you for your feedback!
-
The TV input is a single audio input with different options for connectors. If an HDMI cable is connected, then it will always be prioritized. Optical and coaxial digital will be prioritized by first signal present (Be aware, that some optical outputs will register as signal always)
It is not possible to change between the digital inputs for TV source via the remote control.Was this helpful? Thank you for your feedback! -
It is possible to connect a wireless Citation Sub or Sub S to the Citation Amp.Was this helpful? Thank you for your feedback!
-
The two earpieces of your TWS headphones should normally be connected together without issue. However, if they are no longer paired to each other, please follow these steps, in order.
- Forget/unpair the headphones on your device.
- Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
- Pair the headphones to your device and see if this resolves the problem.
- If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
- Initiate a Product Reset to reset the earbud’s Bluetooth connection.
- Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
- Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
- Manually pair the 2 buds together again, as you did in step 2. This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
- Pair the buds to your Source Device.
Was this helpful? Thank you for your feedback! -
Yes, by using the manual setup procedure it is possible to increase the signal volume level to the subwoofer, while reducing the level on the subwoofer itself. The reason it switches off is that the standby sensing circuit cannot sense music when the level is very low. By increasing the volume to the subwoofer and reducing its output on the sub itself, the signal sensing circuit has a better chance of recognizing an incoming signal, preventing the sub from switching off.Was this helpful? Thank you for your feedback!
-
Move the sub closer to the SOUNDBAR for testing and see if the signal picks up. 1: Turn off any wireless routers or devices that run on 2.4ghz signals, such baby monitors, cordless phones, etc. and test to see if the subwoofer connects. 2: Test with a movie or music with a lot of action scenes or bass. If it's just dialogue, you may not hear the subwoofer.Was this helpful? Thank you for your feedback!
-
If you experience a problem with setup using an Android 7.0 or higher device, please perform the following steps: First, force stop the HK Controller app from running in background. Second, go to your phone or tablet Wi-Fi settings, find the Omni speaker setup Wi-Fi network, and select “Forget Network”.Third, reopen the HK Controller app and begin the setup process again. After performing these steps, you will be able to complete the setup process for your speakers.Was this helpful? Thank you for your feedback!
-
Verify your TV supports the ARC feature.Make sure you enable the external speakers/ARC/digital audio output on your TV, this varies by TV manufacturer. Set the AVR1x1S to the TV input. Go into the AVR menu settings and under System Settings, make sure Audio Return Channel is set to Auto and set the TV Control to on.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
WhatsApp Us
Chat with a support agent via Whatsapp at:
by clicking https://bit.ly/2SfFSPh or send hi to 91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)