How To
How To
-
Check out this JBL In-Ear Fit Guide video, or read the below article.
In-Ear Fit GuideA proper fit is the most important thing when using in-ear headphones (wired, wireless, TWS). Without a solid, tight fit the headphones will sound thin (lacking bass), not very loud, and will do a poor job of blocking out unwanted sounds.
In-ears, unlike an earbud design, are meant to be pushed into your ear canal, creating a tight seal. If this seal is not accomplished, you will not experience good results.
- Typically speaking, the medium sized ear tip is already installed on your in-ear headphones. If it feels tight or loose, try the other sizes.
- As you try each ear tip, rotate forward and/or back until you create a tight seal as seen here.
NOTE: The image shows a stick style in-ear, but this applies to any in-ear design. - As you are twisting and pushing you will hear the sound quality changing. When you accomplish a tight seal, you’ll hear it. You will have more bass than in any other position, and the leakage from outside noise will be minimized before ever turning on Noise Cancelling (if your headphones have Noise Cancelling).
- If you have one of our headphones that uses the JBL Headphones App, check in the app to see if there is a “Check My Best Fit” banner. This feature will walk you through getting the best fit and will let you know when you’ve accomplished it.
While this may seem a bit daunting, after doing this a few times, inserting the in-ear headphones into your ears and getting a good fit will become second nature and will take a second or two each time, not minutes. But it is definitely worth spending the few moments the first time around, in order to get the most out of your in-ears.
Was this helpful? Thank you for your feedback! -
The 12V trigger output can be used with a stereo 3.5mm jack cable. The 12v trigger signal is present in the ring/right-ch connection.Was this helpful? Thank you for your feedback!
-
There are several ways to access the advanced settings. In the settings page, you can adjust settings for subwoofer, EQ and input sensitivity.
Make sure your PC or smartphone is connected to the same network as Citation AMP:
1. On a PC, go to the "Network" folder". There you can find an icon for the Citation Amp. Double click that, and you are taken to the internal webpage for advanced settings for your Citation Amp.
2. Or, in the Google Home app, go to settings for the Citation Amp. At the bottom of the page, you can find the device IP address. Copy and paste this address into your web browser, and you are taken to the internal webpage for advanced settings for your Citation Amp.Was this helpful? Thank you for your feedback! -
High pass filter
When the subwoofer is connected, the main channels are "Small", meaning that there is a high-pass filter. This ensures proper blending with the subwoofer.
Crossover settingsThe Citation amp supports crossover settings in the range 50Hz - 120Hz. Default is 80Hz.
Multiple subwoofers?Only one type of subwoofer is supported at a time. Either with cable or wireless.
Was this helpful? Thank you for your feedback! -
This happens if you power up the subwoofer before connecting the right and left speakers. The system mutes to avoid potentially harmful pop noise. Just touch one of the volume up/down pads to unmute.Was this helpful? Thank you for your feedback!
-
This is because most Windows do not support A2DP stereo audio streaming via Bluetooth, the standard for music-listening through Bluetooth. The system will support keyboards, mice, printers etc. via Bluetooth, but not audio. It is necessary to download the proper drivers, either from the computer manufacturer, the software manufacturer or the manufacturer of the Bluetooth chip in the computer. Help to do this must be sought with the companies that supply one or more of these computer features.Was this helpful? Thank you for your feedback!
-
AirPlay uses a differnet network card inside the BDS. If it doesn't receive any IP adresses, it won't work. To check and see if your network card in BDS did receive an IP address, you can use an app called Net Analyzer for iOS and WiFi Analyzer for Android. Simply scan your network with one of them, and you should be able to see your BDS IP address, usually the IP after your main IP for BDS, should be AirPlay network details. If you have trouble, please contact our helpdesk for further assistance.Was this helpful? Thank you for your feedback!
-
No, shipping is on us. You can send your order back within 30 days for a full refund.
To initiate a return request, click here.
Was this helpful? Thank you for your feedback! -
If the Harman Kardon Go + Play is not stable or wobbles on a surface, one of the legs on the bottom of the speaker is adjustable with a Philips screwdriver. The adjustable leg is the one with a screw is in the center of the leg.Was this helpful? Thank you for your feedback!
-
The product packaging is made from FSC-certified material and printed with soy ink.
Was this helpful? Thank you for your feedback! -
No. The speakers are in the front where the logo is located.Was this helpful? Thank you for your feedback!
-
Yes, this is correct. The AVR 1x1S does not support OSD on HDMI 2 out, only on HDMI 1.Was this helpful? Thank you for your feedback!
-
Yes, this is correct. The AVR171, 171S, 1710 & 1710S only supports OSD on on the HDMI 1 output. HDMI 2 doesn't not show the OSD. The AVR370 and 3700 supports OSD on both HDMI outputs.Was this helpful? Thank you for your feedback!
-
If you are having trouble with distortion or drop out, try the following suggestions:
Move the audio source closer to the speakers
Move the speakers closer to each other
Make sure the streaming speaker (host) only connects to one audio source, disconnect the Bluetooth connection between the streaming speaker (host) and other audio source
Make sure the audio source only connects with one streaming speaker (host), disconnect the Bluetooth connection between the audio source and other speakers
Restart both your speakers and the audio source
Make sure speakers are away from other sources of wireless signal – you could be experiencing interference
Re-pair the audio source with your speaker
If you’re streaming audio content from the internet, the issue could be with the internet connection and not your speakerWas this helpful? Thank you for your feedback! -
Check to see if it happens with all source devices (TV, BluRay, DVD, etc.). If it only happens with one device and not the other, the issue may be with that device. Make sure you do not have any HDMI adapters or splitters. These can cause issues with video and audio.Was this helpful? Thank you for your feedback!
-
The Aura Studio has been put into demo mode, here is how to detect and disable this feature.
How to detect "demo mode" on the Aura Studio:- When plugged in, the Aura Studio will stay powered on at all times (it will not go into standby mode).
- All buttons on the speaker will not work.
- Bluetooth mode is disabled, wireless connection will not work.
- Only the aux cable input can be used to play music; volume is automatically set to maximum and cannot be adjusted (all buttons are disabled).
How to disable "demo mode" on the Aura Studio:- Make sure the speaker is powered ON.
- Press and hold the Vol - and Bluetooth button for at least 5 seconds
- The speaker will power OFF, demo mode is disable.
- Now when the speaker is powered ON, you will have full access to all buttons and features.
Was this helpful? Thank you for your feedback! -
Many Harman Kardon, JBL and AKG products run on rechargeable batteries. In most cases, these batteries will provide years of excellent service and keep the music playing for many hours.
WARNING – the rechargeable batteries inside our products are not user-serviceable. Please do not attempt to open the product or replace the battery. Doing so will void your warranty.
Battery issues fall into three categories:
-
Your speaker or headphones run out of power after only a short time.
-
The speaker will not play at all because the battery will not hold a charge.
-
When you plug in the cable to charge your speaker, sometimes it charges and sometimes it does not- the red charging LED or other indicator might not come on.
Here are some things to try that often fix these issues.
-
It could be as simple as a bad USB charging cable. If you have other charging cables, give them a try. (Be sure that the cable has the same type of connector as the original one that came with your product.)
-
Same for the charger- if your product charges by USB, try a different USB charger. Be sure that it is rated at least 2.0a (2 amps) output.
-
Try other electrical outlets at your location to be certain it is not a local wiring issue.
-
Charge the product overnight for at least 8 hours.
-
When you plug the charging cable into the speaker or headphones, is the connector stable, or can it be wiggled around? If it can be wiggled, this could indicate that the charging port has been damaged or come loose. Sometimes wiggling the connection restores charging power.
IMPORTANT: Some products such as Xtreme, Xtreme 2, Boombox, Partybox 100 & 300, GO+Play and the Onyx Studio series do not use USB charging. Instead, they have a specialized charger. Do not attempt to charge these products with other cables or chargers.
If none of these fixes the issue, it could be that the battery has died or is losing its capacity, or that the charging connector on your speaker is damaged. Please contact us so we can assist you. Be sure to mention that you have tried the steps in this Battery & Charging FAQ so that our agents do not ask you to repeat these steps.
Was this helpful? Thank you for your feedback! -
-
Getting started with the checklist
- A Harman Kardon Citation device(s).
- Latest version of the Google Home app installed on your mobile device.
- Latest version of the Google app (Android only) installed on your mobile device
- A Google Account (you can create one online via Google).
- A mobile device with either iOS or Android support.
- Must have iOS 10 or higher
- Must have Android 5.0 and higher
- There is no support for PC set up.
- Your mobile device must support 5 GHz Wireless Network connection in order to set up our Harman Kardon Citation device. Note: Wireless Network with WPA2-Enterprise encryption is not supported.
- An internet connection from your local ISP (Internet Service Provider).
- Your Wireless Network must secured with WPA2 Encryption (Enterprise mode NOT supported).
- Availability and performance of certain features, services and applications are device- and network-dependent and may not be available in all areas; subscription(s) may be required, and additional terms, conditions and/or charges may apply.
Was this helpful? Thank you for your feedback! -
Three things to know about Bluetooth (BT)…
1. Pairing: Pairing is like creating a new contact in your phone’s Contacts list. You have to do a little bit of work to create the contact, but once you do, connecting with that person in the future is fast and easy.
Let’s put this in terms of phones and speakers (or headphones). Your phone needs to become acquainted with your speaker. This is called pairing.
NOTE: Throughout this article, we will talk about your phone. However, it applies the same to tablets, laptops, computers and any other Bluetooth (BT) source device.To get this started, you have to put the speaker into pairing mode. You may have to press a few buttons to make this happen. All speakers work a little differently, but generally speaking, follow these steps…- For most speakers, quickly press and release the speaker’s BT button. However, with some speakers you may have to press and hold the BT button for a few seconds. Most speakers make a noise or have a blinking LED to let you know they are in pairing mode.
If this does not get you into pairing mode, check your owner’s manual or look for an article pertaining to your specific speaker. - Go into BT settings on your phone. Search or scan for available devices.
- A list of available or discoverable devices will appear on your phone. Select your speaker.
- Two things have just occurred:
- Your phone and speaker are now paired.
- Your phone and speaker are now connected so that you can listen to music.
NOTE: Just as you can have many people in your phone’s Contacts list, you can have many speakers and headphones in your phone’s paired devices list.2. Connecting: Once you have paired, your phone remembers your speaker, and your speaker remembers your phone. However, the two must connect to play music through the speaker.Automatic Re-connection: Let’s say your speaker is at home in the living room, and you leave for the day. When you come home and are within range of the speaker, your phone will automatically re-connect to it (assuming it is turned on). You can press play on your phone, and the music will play though your speaker. Of course, if your speaker is off, you will need to turn it on first. NOTE: Some speakers make a sound when they re-connect.
Automatic re-connection does not always happen.- Some phones may not work like this.
- Someone else may have connected to the speaker.
- Perhaps you connected to a different speaker while outside of your home.
Manual Re-connection: If your device does not automatically re-connect, you can re-connect manually…- Go into Bluetooth settings on your phone and make sure BT is on.
- Select your speaker to re-connect and play music.
Some speakers allow several phones to be connected at the same time. Others allow only one at a time. Therefore, if you are unable to re-connect, it could be that some other phone is connected to the speaker. In this case…- Go into the other phone’s BT settings and disconnect the speaker or turn off BT.
- Then follow the steps above to manually re-connect your phone to the speaker.
NOTE: Do NOT Unpair or Forget the speaker in your phone’s BT settings, as this will require you to repeat the Pairing steps above.
3. Resetting: This is a drastic step and should only be done if the unit is not operating correctly. Do NOT reset your speaker every time you want to connect. Resetting erases all pairings to all phones. You would then have to Unpair or Forget this speaker from each and every phone, and start the pairing process all over again. Check your owner’s manual or look for an article with more detailed BT instructions on your specific speaker or headphone model.Was this helpful? Thank you for your feedback! - For most speakers, quickly press and release the speaker’s BT button. However, with some speakers you may have to press and hold the BT button for a few seconds. Most speakers make a noise or have a blinking LED to let you know they are in pairing mode.
-
If the buttons on your portable speaker are not working properly or are unresponsive while plugged into a power source, please try running the speaker on battery. If the buttons perform correctly while running on battery, this means your power supply is not providing enough current/amps. Be sure to use a power supply that has a rating equal to or greater than the amperage rating indicated in your product specs.Was this helpful? Thank you for your feedback!
-
The BDS 280/580 or 280S/580S can upscale video signals from its internal drive to UHD format, both DVD and Blu-ray discs. The 280/580 or 280S/580S have pass-through function on the HDMI inputs. They will not upscale standard format or normal HD format video signals that are fed to the HDMI inputs of the 280/580 or 280S/580S. However, 4K or UHD video signals will pass through the BDS directly to the TV screen without processing, as will HD and SD format video. (Bear in mind that this high resolution makes it even more important to use high-quality HDMI cables, especially if they must be several meters long.)Was this helpful? Thank you for your feedback!
-
Many newer routers with auto detect work really well. But if you experience issues with your product, we advise you to disable this feature and have two visible Wi-Fi networks (2.4 GHz and 5 GHz network).Was this helpful? Thank you for your feedback!
-
No, 4K upscaling is not possible. It was mentioned in the specification sheet and on the web page that this feature was supported, but that is an error.Was this helpful? Thank you for your feedback!
-
Once the order has been placed, it cannot be changed online. If you want to change your order, please call the phone number posted at the top of this page, and if it has not yet been processed we will change or re-issue a new amended order.Was this helpful? Thank you for your feedback!
-
You can charge your mobile Phone, but not mobile tablets.Was this helpful? Thank you for your feedback!
-
Yes, press and hold microphone mute button & volume - button at the same time. A voice will speak up some numbers, that indicate the current software version in your ESQUIRE 2.Was this helpful? Thank you for your feedback!
-
Yes, hold down the Volume and Bluetooth buttons at the same time. A voice will call out some numbers, and that is the software version on your AURA Studio.Was this helpful? Thank you for your feedback!
-
Yes, in the HDMI Setup Menu, it is possible to select either �Sound To TV� or �Sound To Amp�, Amp being the AVR. This detail is not mentioned in the owner's manual.Was this helpful? Thank you for your feedback!
-
Yes, in the HDMI Setup Menu, you can select either Sound To TV or to Amp, (which is the AVR 70). This detail is not mentioned in the owner's manual.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call us
Talk to a product expert
Call us now at:
(800) 422-8027
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)
Chat with us
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)