AVR 240

AVR 240

Audio/Video Receiver With Dolby Digital & DTS (65 watts x 2 | 50 watts x 7)

Sold from 2005 until 2006

Predecessor Product: AVR 235
Successor Product: AVR 245
Made in: China

Documents & Downloads

Product Specifications

Power Requirements
AC 220 – 240V / 50Hz
Power Consumption
118W idle, 890W maximum (7 channels driven)
Digital Inputs (coaxial/optical)
2/2 on rear; 1/1 on front
Analog Inputs
1 A/V on front panel
Analog Inputs
2 audio-only
Analog Inputs
4 A/V on rear panel
Analog Inputs
6-/8-channel input
Analog Inputs
tuner
On-Screen Display
Yes
Multizone Capability
No
Auto Setup
EzSet remote
Remote Control
Eight-device, programmable remote
MSRP U.S.
$599.95 each
# of Amplifier Channels
7
Continuous Average Power (FTC) per Channel (stereo mode)
65 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms
Front L & R Channels
50 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Center Channel
50 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Surround Channels (L & R Side, L & R Back)
50 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Input Level/Impedance
200mV/47k ohms - Linear (High-Level)
Signal-to-Noise Ratio
100dB (IHF-A)
Surround System Adjacent Channel Separation:
Dolby Pro Logic I and II
40dB
Dolby Digital
55dB
DTS
55dB
Frequency Response
10Hz – 130kHz (+0/-3dB @ 1 watt)
Transient Intermodulation Distortion (TIM)
Unmeasurable
Slew Rate
40V/µsec
Width
17.3 inch (440mm)
Height
5.9 inch (150mm)
Depth
13.8 inch (350mm)
Weight
24.4 lb (13.9kg)
Dimensions:
Television Format
PAL/NTSC
Input Level/Impedance
1Vp-p/75 ohms
Output Level/Impedance
1V/75 ohms
Video Frequency Response:
Composite and S-Video
10Hz – 8MHz (–3dB)
Component Video
10Hz – 50MHz (–3dB)
Frequency Range
AM... 520 – 1720kHz
Frequency Range
FM... 87.5 – 108.0MHz
Signal-to-Noise Ratio
AM... 45dB
Usable Sensitivity
FM... IHF 1.3µV/13.2dBf
Signal-to-Noise Ratio
FM... Mono/Stereo 70/68dB
Usable Sensitivity
AM... Loop 500µV
Distortion
AM... 1kHz, 50% Mod 0.8%
Distortion
FM... Mono/Stereo 0.2/0.3%
Selectivity
AM... ± 10kHz, 30dB
Stereo Separation
FM... 40dB @ 1kHz
Selectivity
FM... ± 400kHz, 70dB
Image Rejection
FM... 80dB
IF Rejection
FM... 90dB
Amplifier Power (RMS)
50 x 7 @ 8 ohms (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
High Instantaneous Current Capability (HCC)
± 35 Amps

FAQs & How-Tos

2 results
  • This receiver has a feature called "A/V Sync Delay" that allows you to manually set dissimilar video and audio synchronization that may occur with certain types of Plasma and HDTV's. The instruction for this setting can be found in your owner's manual in the section "Delay Adjustments" or "Delay Settings".
  • The remote is only capable of operating one device at a time (unless you have programmed advanced functions such as Volume, Channel or Transport control Punch-Through). When you press the Source Selector to operate your other product, such as the DVD player, the remote cannot control any other product, including the AVR, until you press the AVR Button again. To avoid your problem in the future, always press the AVR Button or appropriate Source Selector before you enter any command.

Can’t find what you’re looking for?

Call us

Call us

Talk to a product expert
Call us now at: (800) 422-8027

Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)

Chat with us

Chat with us

Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)