AVR 2600

AVR 2600

Audio/Video Receiver With Dolby TrueHD & DTS-HD Master Audio, HDMI 1.3A & 1080p Upscaling (65 watts x 7)

Sold from 2009 until 2012

Successor Product: AVR 2650
Made in: China

Documents & Downloads

Product Specifications

Power Consumption (full power/idle)
120W idle, 1405W maximum
Transient intermodulation distortion (TIM):
Unmeasurable
Power Requirement
AC 120V/60Hz
Power Requirements
AC 120V/60Hz
Power Consumption
65W idle, 540W maximum (7 channels driven)
Digital Inputs (coaxial/optical)
2/2 on rear; 1/1 on front
HDMI
Four inputs/1 output, with audio and video processing. HDMI v.1.4a with 3D.
Analog Inputs
1 A/V on front panel
Analog Inputs
2 audio-only
Analog Inputs
4 A/V on rear panel
Analog Inputs
6-/8-channel input
Analog Inputs
stereo jack
Analog Inputs
tuner
On-Screen Display
Yes, with component video and HDMI
Multizone Capability
Yes, by reassigning surround back channels only
Auto Setup
EzSet/EQ room equalization
Remote Control
Seven-device, programmable remote
MSRP U.S.
$799.95 each
Distortion (Mono/Stereo)
0.2/0.3%
Frequency Response
10Hz –130kHz
Surround system adjacent-channel separation:
Pro Logic® I/II 40dB Dolby® Digital (AC-3) 55dB DTS® 55dB
High Instantaneous Current Capability
±60 Amps
Input Level/Impedence (ohm)
1Vp-p/75 ohms
Stereo Separation @ 1kHz (dB)
40dB @ 1kHz
Output Level/Impedence (ohm)
1Vp-p/75 ohms
Signal-to-Noise Ratio (dB)
45dB
Signal-to-Noise Ratio (Mono/Stereo dB)
Mono/Stereo 70/68dB
Selectivity (±400kHz):
70dB
Signal-to-noise Ratio (IHF-A) (dB)
100dB
Usable Sensitivity (Loop)
500?V
Frequency Range (kHz)
520–1720kHz
Input Sensitivity/Impedence
200mV/47k ohms
Distortion (1kHz, 50% mod):
1kHz, 50% Mod 0.8%
Stereo Power
65 Watts per channel, 20Hz–20kHz, @ <0.07% THD, both channels driven into 8 ohms
Frequency Range (MHz)
87.5–108.0MHz
Slew Rate
40V/sec
Usable Sensitivity (IHF)
IHF 1.3?V/13.2dBf
Selectivity (±10kHz):
30dB
# of Amplifier Channels
7
Continuous Average Power (FTC) per Channel (stereo mode)
65 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms
Front L & R Channels
65 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Center Channel
65 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Surround Channels (L & R Side, L & R Back)
65 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Input Level/Impedance
200mV/47k ohms - Linear (High-Level)
Signal-to-Noise Ratio
100dB (IHF-A)
Surround System Adjacent Channel Separation:
Dolby Pro Logic I and II
40dB
Dolby Digital
55dB
DTS
55dB
Frequency Response
10Hz – 130kHz (+0/-3dB @ 1 watt)
Transient Intermodulation Distortion (TIM)
Unmeasurable
Slew Rate
40V/µsec
Height (mm)
165
Depth (in)
17-1/16
Width (mm)
440
Depth (mm)
435
Height (in)
6-1/2
Weight(kg)
20
Width (in)
17-5/16
Width
17-5/16 inch (440mm)
Height
6-1/2 inch (165mm)
Depth
17-1/16 inch (435mm)
Weight
26lbs
Shipping Weight (System, Accessories, Packing)
32lbs
Carton Dimensions (W x H x D)
21-7/8 inch x 10-1/2 inch x 18-5/16 inch (555mm x 266mm x 465mm)
Video Frequency Response (Component Video)
10Hz–100MHz (–3dB)
IF Rejection (dB)
90dB
Television Format
NTSC
Image Rejection (dB)
80dB
Input Level/Impedance
1Vp-p/75 ohms
Output Level/Impedance
1V/75 ohms
Video Frequency Response
10Hz–100MHz (–3dB)
Composite and S-Video
10Hz – 8MHz (–3dB)
Component Video
10Hz – 100MHz (–3dB)
HDMI
HDMI v.1.4a with 3D.
Frequency Range
AM... 520kHz – 1720kHz
Frequency Range
FM... 87.5MHz – 108.0MHz
Signal-to-Noise Ratio
AM... 45dB
Usable Sensitivity
FM... IHF 1.3µV/13.2dBf
Signal-to-Noise Ratio
FM... Mono/Stereo 70/68dB
Usable Sensitivity
AM... Loop 500µV
Distortion
AM... 1kHz, 50% Mod 0.8%
Distortion
FM... Mono/Stereo 0.2/0.3%
Selectivity
AM... ± 10kHz, 30dB
Stereo Separation
FM... 40dB @ 1kHz
Selectivity
FM... ± 400kHz, 70dB
Image Rejection
FM... 80dB
IF Rejection
FM... 90dB
Amplifier Power (RMS)
65 x 7 @ 8 ohms (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
High Instantaneous Current Capability (HCC)
± 35 Amps

A 7.1-channel A/V receiver with HDMI 3D plus Dolby, DTS and Logic 7 surround.

The AVR 2600 is designed to delight the most discerning home theater enthusiast. With its high-definition on-screen interface and Logic 7® technology, the AVR 2600 is prepared to bring the home theater experience to an entirely new level. Along with its state-of-the-art Faroudja DCDi Cinema™ processing, Dolby® audio technology and HDMI® v.1.4A playback with 3-D capability, this home theater powerhouse can even sync up with The Bridge III docking station (available separately), allowing you to enjoy movies, music, or multimedia files straight from your iPod® or iPhone®.

The AVR 2600 high-performance receiver delivers 65 watts per channel with the ability to power a full 7.1-channel surround-sound system. A high-current capability (HCC), ultrawide-bandwidth amplifier design ensures accurate, dynamic sound with enhanced clarity and realism, even at the highest listening levels. You can also connect the AVR 2600 to a powered subwoofer to generate additional low-frequency excitement.
Four HDMI inputs with 3D and Deep Color deliver high-definition digital video at resolutions up to 1080p with full-fidelity audio through a single cable. There is no loss of video or audio quality because of format conversion, just full-impact Hollywood excitement as its creators meant you to experience it.
The AVR 2600 delivers high-resolution audio to match the digital video of Blu-ray Disc formats, unlocking the full potential of movie soundtracks formatted with Dolby TrueHD and DTS-HD Master Audio coding. No matter what mode or mood you are in, you’ll always hear playback at its finest.
Dolby Volume technology maintains the same volume level no matter what entertainment you’re viewing. You need to set the AVR 2600 volume level only once to eliminate unpredictable volume differences among TV shows, commercials and movies.
HARMAN Logic 7 technology transforms a stereo input into full 7.1-channel surround sound, courtesy of proprietary algorithms that make any audio source – HDMI, analog, component, composite or computer-based audio from a USB connection – truly spectacular. The result is optimal quality and a superior, enveloping experience that engulfs you in a 360-degree soundscape.
Four HDMI input ports let you digitally interconnect your entire system for maximum audio/video performance. HDMI-format ports dramatically reduce connection confusion while ensuring the greatest chance for compatibility with whatever audio/video equipment you are planning to connect.
The HARMAN EzSet/EQ™ auto-calibration process tailors the AVR 2600’s loudspeaker outputs to match playback volume levels for your specific room conditions automatically. The system features an easy-to-follow menu display and a plug-in calibration microphone.
The optional Harman Kardon The Bridge IIIP docking station (sold separately) works with an Apple iPod or iPhone to expand your entertainment options beyond DVD and Blu-ray Disc media. Once connected, The Bridge III even charges your Apple device and works seamlessly with the AVR 2600’s system remote control to navigate and play your favorite music and video tracks.
Faroudja DCDi Cinema processing dramatically reduces video artifacts from digital or analog signals. The result is fewer lines and a smoother picture – especially when there is movement across your TV screen. Faroudja DCDi Cinema technology also upscales lower-resolution video to the 1080p high-definition standard, thereby extending the life of your movie library.
A built-in MP3 enhancer dramatically improves bass performance when replaying compressed-audio tracks, thereby elevating the sound quality of your favorite songs without the need for additional audio equipment.

Can’t find what you’re looking for?

Call us

Call us

Talk to a product expert
Call us now at: (800) 422-8027

Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)

Chat with us

Chat with us

Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)