How To
How To
441 results
-
Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.Was this helpful? Thank you for your feedback!
-
To prevent other people from changing the source on your BDS through Bluetooth, you can disable the “Automatic Playback” function in the System Settings of the BDS ( 280, 580, 280S and 580S ). This does not prevent others from connecting to one of the two Bluetooth receivers in the BDS units, but it prevents other people from “interrupting” your playback source. This is where the change is done: Settings – System Settings Automatic Playback ( Enable/Disable ) Enabled: People can connect to your BDS and start playing music/audio. Your BDS will automatically change source ( or switch on, when BDS is in Standby mode ) from any source. Disabled: People can connect to your BDS, but the BDS will not automatically change source, or go out of Standby mode when a music/audio signal is sent through Bluetooth.Was this helpful? Thank you for your feedback!
-
We have some suggestions if you want to enjoy the best performance from your Bluetooth devices. 1. Please note that if you have a large number of Apps open in your smartphone or tablet, this may block or overtax its processor. Dropouts may result. Try to close all or most active apps. This should solve the problem. 2. Bluetooth signals from smartphones and tablets are not very strong. Make sure that the signal does not have to pass through doors, walls etc. Always maintain a clear line of sight between transmitter and receiver. 3. Do not carry your smartphone in your pocket, if you have dropouts. Your body can act as a screen, reducing the strength of the Bluetooth signal. Put the phone on a table or other surface. 4. Do not walk around while listening. If the transmitter and the receiver are moved in relation to each other, dropouts occur more frequently. 5. Under normal circumstances, you can expect a range of 5 meters with no problems, if you follow the above advice. In some instances range is longer, but we cannot promise this.Was this helpful? Thank you for your feedback!
-
That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".Was this helpful? Thank you for your feedback!
-
Once the speaker/soundbar is connected to the network, software updates will automatically be sent to the product through Wi-Fi or the internet, if available
Was this helpful? Thank you for your feedback! -
For Citation ONE, Citation 100, Citation Sub and Citation Surround, Press and hold the RESET button on the speaker for 5 seconds. For Citation 300, Citation 500, Citation Bar and Citation Tower, Press and hold the RESET button on the speaker for 5 seconds, or select the Factory Reset option in the touch screen settings menu.Was this helpful? Thank you for your feedback!
-
Press the Bluetooth source button on your BDS remote. In the right top corner of your TV screen, there should be a button called "Pair". Jump to the "Pair button" to perform pairing by using the arrow keys on your remote control. Click OK while being on the pair button. Once pressed, a pop-up screen will appear, this indicates pairing mode is active for 3 minutes. Go to Bluetooth settings on your mobile device, find the BDS in the list and connect. If you want to pair a second device, please repeat the procedure to activate pairing mode.Was this helpful? Thank you for your feedback!
-
You can delete specific voice recordings associated with your account by going to History in Settings in the Alexa App, drilling down for a specific entry, and then tapping the delete button. Or, you can delete all voice recordings associated with your account for your Harman Kardon Allure speaker, by selecting the applicable product at the Manage Your Content and Devices page at www.amazon.com/mycd. and deleting voice recordings. However, this may degrade your Alexa experience.Was this helpful? Thank you for your feedback!
-
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback! -
HDMI Output
Both Enchant 800 and Enchant 1300 support these:- HDMI 2.0b compliance
- HDCP 2.2 compliance (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
- CEC features (Scroll to see support)
HDMI Input
Enchant features only 1 x HDMI input, and Enchant has 3 x HDMI inputs and support this:- HDMI 2.0b.
- HDCP 2.2 for all HDMI input connections (Means it supports 4K Blue-Ray Movies or streaming clients with 4K encryption)
- 4K Pass-through.
CEC Support
CEC support only available through your HDMI connection and we are always using standard protocol for our products.
We support these:- System Standby: When you press the "Power off" button on your TV remote, the Enchant soundbar will go into Standby mode as well.
- ARC or called Audio Return Channel: If you would have a TV BOX connected directly to your TV and using ARC from TV to Enchant soundbar, then all sound will be transferred through ARC connection.
- In case you are not using the HDMI ARC connection then sound coming from the TV show will not be transferred to the Enchant soundbar.
- System Audio Control: Using your TV remote to turn up or lower the volume will be synchronized with the Enchant soundbar.
Bigger model is the Enchant 1300 and smaller model is the Enchant 800.Was this helpful? Thank you for your feedback! -
The Citation Amp works with Chromecast built-in (audio only), and also works with Hey Google products. For example, you can use voice commands to tell your other Google speakers to play music on Citation Amp. Was this helpful? Thank you for your feedback! -
To reset the device to its factory settings:
Power on the speaker. While on, press and hold the power button down for 15-20 seconds until the speaker turns off.
Now that the speaker has been reset, make sure to remove it from your BT settings if it was once paired to other devices as the BT memory has been reset as well. Once you turn the speaker on again, it should automatically enter into pairing mode with a flashing LED. It should pop up on your discoverable devices under your BT settings and connect within a few seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday – Friday: 08.00-17.00
Saturday – Sunday : 09.00–15.00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00