This function is not available on these BDS units. So-called five-channel stereo is a feature which is available in Harman Kardon AVR surround receivers, but it has not been included in the BDS platform.

Yes, it can be done very easily. 1: First power on your AURA Studio. 2: Press volume + and Phone button at the same time for 5 seconds. 3: All LED light indicators will flash for 1 second. 4: Your AURA Studio has been reset.

Yes, press and simultaneously hold down the Aux and the Zoom (Blue) buttons on the BDS remote control for at least three seconds. The input selector panel buttons all flash three times.

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the Wireless speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the Wireless connected speaker and Google Assistant request.

 

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the Speaker and Google Assistant request.

 

The speaker is IPX5 certified, it can withstand direct splashes from any direction for up to 3 minutes. Although a little snow or rain won't hurt it, we do not recommend keeping the speaker outside during rain and/or snow. Also be aware of extreme hot or cold temperatures, they may be damaging.

To connect and play music from a second source device using multi-point connection, simply press the Bluetooth button and connect to the product in the settings of the source device.

When using multi-point connection and switching between iOS, Android and Windows, there may be no music output or a delay in music playback. To resolve this issue, it is always recommended to pause or stop music playback on one Computer/PC/Laptop before multi-point switching to another device (Phones, Tablets) for music playback.

If the issue persists, we recommend to restart both the product and the Computer/PC/Laptop.

You can create a multi-room setup using Chromecast built-in™ or Airplay, linking to other speakers with the same feature including the Harman Kardon Citation Series.

The Aura only goes from sleep mode to stand-by mode if you either press Power Off, or leave the Aura inactive for 30 minutes with no wifi connection established. Please note that the power light dims when Aura enters sleep mode, but extinguishes completely in stand-by mode. Please note that in both Sleep and Standby modes, Bluetooth remains active, and Aura will wake up if BT transmission is received.

To use the speaker as PC speaker, please make sure your PC supports our Bluetooth specifications and specifically A2DP Codec for Stereo Audio streaming

There are five possible reasons for the receiver shutting down. 1. There is a problem internally with the receiver. 2. There is a problem with one or more of your speakers. 3. There is a problem with one or more of your speaker wires. 4. There is a problem with the speaker wiring done on your system. 5. The unit is overheating. No ventilation. First, check the wiring at every speaker terminal at the back of your receiver and at the back of your speakers. A single strand of speaker wire crossing from one terminal to another would be enough to cause the amp to shut down or go into PROTECT. If you do not find any problems with any of the wiring, you should disconnect all speakers from your receiver. If the receiver continues to go into PROTECT, the problem is in the receiver. Please submit a case on the Contact Us page. They will be able to assist you. However, if it turns on, the problem is elsewhere. Begin reconnecting one speaker at a time. Eventually you will connect a speaker that will cause the receiver to shut down. At this point you have found your culprit. On the other hand, it may just be overheating. You must have at least 2 - 3 inches of space between the top of the unit and any shelf or component above the unit. The unit should not be inside a sealed compartment when being used. The unit must be able to breath. There are very powerful amps in these receivers. If they run too hot, they will shut down. An external fan can help this.

If you have enabled HDMI-link (CEC function), then you will experience that your AVR will do some actions based on the CEC function coming from your TV, which in this case it will follow your TV when it goes into standby.

Yes, playlists in these BDS units have an upper limit of 100 files.

We always recommend to use the online updating tool inside BDS, as it is connected directly to our server and if new software are available, it will be there first. We are trying to update our website as quickly as possible.

This can be caused by many things. It could be obstacles between your device and router, or that your device has been placed too far away. To enhance the WiFi signal for your BDS, please make sure to place the included antenna on its threaded socket, then try search for any WiFi network again. If this still does not work, try moving your BDS closer to the router until connection is established, ensuring that the BDS WiFi network module is working. If nothing happens, the network module of the BDS or your router have a problem. In case you need more help, contact our support for more tips.

Make sure your home network's Internet connection is active and the Citation speaker is placed within Wi-Fi range. If you are using a Wi-Fi extender, your speaker may be confused which network to connect to. If this is happening, try moving the speaker closer to the main router and renaming the Wi-Fi extender.

Fortunately the Go+Play in all versions is made with this problem in mind. One of the feet is adjustable. Look at the four feet. One is different from the others. You can insert a 3mm hex key into the center hole in it, then loosen the foot insert and unscrew it until the unit is steady. The adjustable insert may stick a little, so exert a steady, firm pressure to get it loose if this is the case.

The Go+Play Wireless must be in Standby to be able to switch On when receiving a signal. This function uses a small amount of power, and cannot be switched off. Remove batteries when not in use for more than 2 weeks to prevent power draining.

If your Wi-Fi network name has special characters, such as (, `, \, ', ", or ), then please change the name of your Wi-Fi network, as these characters are not supported. After changing the name, you can go ahead and setup the speaker to your Wi-Fi network.

Dual band routers that have 2.4 and 5 GHz connection bands. If devices connect on different bands, they cannot see one another. Please make sure your phone and speakers are both connected to 2.4 GHz or 5 GHz and that there is no AP isolation activated between them.

One explanation can be that your OMNI 50+ is part of a 5.1 system with your Omni Bar, which will make the surround OMNI 50+ left and right rear speakers act as "secondary", and Bluetooth connection is not possible to secondary speakers. To use the OMNI 50+ as a portable speaker again, simply perform a reset of the speaker by pressing the reset button for 5 seconds. Please note that after resetting your OMNI 50+, it is no longer part of the 5.1 wireless system.

Yes, it will power off after removing charging cable. It is by design.

If your parcel is showing signs of damage upon delivery, we recommend that you refuse to accept it.

The parcel will then be returned to our warehouse, and you will automatically receive a refund.

If you already accepted your parcel, please take pictures of the damage(s) before opening the parcel.

We hope that the product(s) you have ordered are without any damage.

If the product(s) are damaged, please contact Customer Support as soon as possible, and no later than 2 days after receival of the parcel as we have a short window to process claims with our delivery partner.

Please note that you must keep all packaging, including the brown shipping box, while our Customer Support team is opening a claim with our delivery partner.

1. Ensure that your Harman Kardon One app device is less than 10m/33ft from the speaker during the initial set-up.
2. Ensure it is plugged into power and the power LED is illuminated.
3. Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
4. Temporarily relocate either the speaker or router so that they are closer together. If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
5. Try using a different device with the Harman Kardon ONE app installed and connected to your home network.