How To
How To
439 results
-
This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products
Was this helpful? Thank you for your feedback! -
Before you start
- Remove any interference that might be blocking the Soundbar side-firing speakers.
- Any ambient noise or sounds that could disrupt the calibration needs to be out of the room.
- In case you are moving the Enchant Soundbar you will need to calibrate the sound again.
- If something went wrong, you can always delete the calibration settings by resetting the system.
- Press and hold
button and
button down for 5 seconds.
- This will delete all settings, including the Wi-Fi connection.
- Press and hold
How to use the MultiBeam feature- Press and hold the CALIBRATION
button for 3 seconds.
- On the Enchant display a timer will start counting down from 3 to 0 (Once hitting 0 the Calibration will begin).
- The calibration takes around 60 seconds before it is complete. While calibrating you will hear some noises coming from the speaker.
- When finished the display on the Enchant Soundbar will say "DONE"
Was this helpful? Thank you for your feedback! -
The power on/off symbol/button will flash white consistently. The LED switches to OFF when charging is complete.Was this helpful? Thank you for your feedback!
-
We do not recommend using WEP encryption method, as this can leave your Wi-Fi vulnerable to outside threats. Our OMNI+ does not support this encryption type, we are supporting WPA and up.Was this helpful? Thank you for your feedback!
-
Make sure you disable AP/Client isolation on your Access Point / Extender and that Multicast forwarding is not disabled between the W-Fi networks. However, we cannot guarantee than streaming will work flawless as Extender networks are tricky and can cause many issues. Always use a 5GHz Wi-Fi network extender for best results.Was this helpful? Thank you for your feedback!
-
Our ESQUIRE2 support A2DP Audio codec, which you will need for your MAC to be able to play to our ESQUIRE2.Was this helpful? Thank you for your feedback!
-
The upgrade via HID tool will only update the Bluetooth module inside of the BDS device. There are two ways of upgrading your system. 1: Upgrading Bluetooth via HID Tool. 2: Upgrade BDS firmware via the built-in software center. The built-in software center will not upgrade your Bluetooth module.Was this helpful? Thank you for your feedback!
-
Unless the two remote controls are identical, you can only assign one remote control at a time to the SB16.Was this helpful? Thank you for your feedback!
-
To use Chromecast, you must continue the setup in the Google Home app first.
Configuring the speaker only with Apple WAC will not enable the Chromecast feature.
For this to happen, you must sign-in with your Google account.
You can quickly try out the Chromecast feature, and if you do not like it, reset your Citation or LINK speaker, and redo the configuration part on your Apple device.Was this helpful? Thank you for your feedback! -
Please try turning Bluetooth off on your phone and trying again, and make sure Location services are enabled for the Google Home app. If this does not work, certain phones are not compatible with the Google Home setup process, including the Vivo X21A, Vivo NEX S, and Vivo X9. Please use a different device for setup.Was this helpful? Thank you for your feedback!
-
Use the Google Voice Assistant button on your Citation soundbar remote control when using these inputs HDMI, AUX or Optical. When you press this button, the current volume level will temporarily decrease and the Google Voice Assistant will begin listening for your command. The reason you need to use the remote control is that Google Assistant does not support Multi-channel audio from your source device (TV, BlueRay Player or TV-BOX) and therefore the mic is automatically muted unless the Google Voice Assistant button is pressed. Google Voice Assistant is always listening when streaming music over Wi-Fi or Bluetooth.Was this helpful? Thank you for your feedback!
-
The built-in YouTube app is able to stream up to 1080P content. Video with higher resolution is not available.Was this helpful? Thank you for your feedback!
-
We designed the USB folder data to show the latest modified folder and it is a design preference. It is not possible to change this setting.Was this helpful? Thank you for your feedback!
-
If you are having problems playing music after setting up a new speaker (no matter what connection is used, Ethernet, Wi-Fi), please restart the Harman Kardon Controller app after the speaker setup is complete.Was this helpful? Thank you for your feedback!
-
Some third-party apps do not support volume changing when your smart device is in lock screen mode.Was this helpful? Thank you for your feedback!
-
If you are experience this message, please power cycle the Wi-Fi router and speaker(s). Disconnect the devices' power cable for 10 seconds and then reconnect them. Once the router and speaker(s) completely boots up, please try to setup again.Was this helpful? Thank you for your feedback!
-
Try reset the ESQUIRE2 speaker. Press and hold Volume + & phone button at the same time. When the unit is reset, it will power off, and turn on the unit again, and it is reset. Go into your Bluetooth device list and delete the ESQUIRE2 from your list. Now Bluetooth pair with it again. If the unit still do not work as intended, please contact our helpdesk.Was this helpful? Thank you for your feedback!
-
This feature is not yet implemented in our Harman Kardon Allure or Allure portable speaker. Future updates might include this option, so we advise keeping an eye on the release notes in the HK Alexa Setup app about possible future firmware updates.Was this helpful? Thank you for your feedback!
-
There may be more than one reasons for this problem, but one detail is important: if establishing the connection manually, do not advance the cursor after having written all characters in your password with the up and down arrows. If you jump to the next empty position after the last character, this will be interpreted as an added character in itself, and the password will be wrong.Was this helpful? Thank you for your feedback!
-
The Harman Kardon Aura Studio 2 only supports Bluetooth. The HK Controller app only works with Harman Kardon products that have WiFi connectivity.Was this helpful? Thank you for your feedback!
-
It is important to use the correct HDMI connection on the BDS, marked with ARC. Also, the proper input must be selected with the AUX input selector button, which scrolls between the six AUX inputs. It always selects the AUX input that you used last, so once you have used the AUX ARC input, the BDS unit remembers it until you select another AUX input. Of course you have to have a TV which actually supports ARC.Was this helpful? Thank you for your feedback!
-
Unfortunately, some Huawei phones are not able to stream music from the HK Controller app to 1st generation Omni speakers. However, the new Omni 10+, 20+, and 50+ have fixed this issue, and you will be able to stream music to them using your Huawei phone.Was this helpful? Thank you for your feedback!
-
Make sure your source device and AURA are on the same network. Then make sure your router is set to support older Wi-Fi protocols, such as b/g where the AURA is operating. Some routers have a function to disable older protocols and only use newer ones.Was this helpful? Thank you for your feedback!
-
It is not possible to setup a speaker to a hidden SSID Wi-Fi network. Please make it visible to install your OMNI+ speakers.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 11:00-16:00
