How To
How To
439 results
-
Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.Was this helpful? Thank you for your feedback!
-
Resetting the Go + Play 3 to Factory Settings:
In power ON mode, press and hold the "Volume +" and "Bluetooth" buttons at the same time for more than 10 seconds.
- The Go + Play 3 will power off and back on and is now reset
Was this helpful? Thank you for your feedback! -
We offer a 30 day free return period. To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.
Was this helpful? Thank you for your feedback! -
In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.Was this helpful? Thank you for your feedback!
-
At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.Was this helpful? Thank you for your feedback!
-
Download the HK Connect app to your mobile device. Make sure that the Onyx Studio 4 speaker is connected successfully to your mobile device. The HK Connect app should recognize the Onyx Studio 4 within the first few seconds. Once inside the app you can activate the voice assistant and connect to other Connect+ Harman Kardon devices.Was this helpful? Thank you for your feedback!
-
Switch device ON.
Press and hold VOLUME+ and PLAY/PAUSE buttons until all lamps light up.
Device is now reset.Was this helpful? Thank you for your feedback! -
Because the Right Ear cup is a touch sensor, you simply have to move your finger from top to bottom on the outside ear cup to increase the volume. In order to decrease the volume, move your finger from the bottom of the ear cup to the top.Was this helpful? Thank you for your feedback!
-
With the table stand, Sabre 35 is 125 mm high and 55 mm deep.Was this helpful? Thank you for your feedback!
-
For the owner, two indications show the difference: 1. In the menu system, a Spotify option is available as one of the tiles. 2. A check of the software version will show 3.16.0 or higher. There is no mention of the Spotify option on the BDS unit itself. For customer service, a serial number check will show the precise model.Was this helpful? Thank you for your feedback!
-
The memory is based on flash memory, and is not forgotten.Was this helpful? Thank you for your feedback!
-
If your OMNI 50+ is completely drained, it will take 3,5 to 4 hours to fully charge. We advise to charge the Omni 50+ when it starts to blink red.Was this helpful? Thank you for your feedback!
-
AURA Studio has the Multi-Connect feature (Social-Mode) which allows you to connect up to 2 devices at the same time and play different music from either device. Note that the music playing on one device will be interrupted when the other device begins playing music, and vice-versa.Was this helpful? Thank you for your feedback!
-
You can have two connectecd devices at the same time.Was this helpful? Thank you for your feedback!
-
As a stand-alone soundbar, the product can support 5.0.2 channels. When connected to the optional Citation Sub or Citation Sub-S, the product can support 5.1.2 channels.
It is also possible to have physical rear surround channels by connecting the optional Citation Surround.
Was this helpful? Thank you for your feedback! -
The amount of Chromecast speakers you can stream music to depends on the bandwidth of your local wireless network. Theoretically, an unlimited amount of devices can be connected to stream the same song.Was this helpful? Thank you for your feedback!
-
Our Multi-Connect feature supports up to two devices, to be connected at the same time. But only one device can play at a time.Was this helpful? Thank you for your feedback!
-
The Vi Personal Trainer is pre-fitted with the size small fin and comes with two additional fin sizes. To get accurate ratings on your heart rate, you'll want to find the fin that fits most comfortably. The Vi also comes pre-fitted with the size medium ear tip and comes with four additional tip sizes. (XS, S, M, L)Was this helpful? Thank you for your feedback!
-
The BDS -75 and -77 models support 2000 files and 10 folder levels on DLNA.Was this helpful? Thank you for your feedback!
-
Three devices can be connected to Go + Play BT/Wireless at the same time. You can easily take turns when playing music from 3 connected devices by pressing play on one of them. If you press play on the second of the connected devices, the first one will be interrupted and the second will start playing, and so on. If you want to connect a 4th device, you'll be required to disconnect one of the connected devices first.Was this helpful? Thank you for your feedback!
-
The speaker uses 4 x 15W when running on battery. You will hear a slight lower bass performance, compared to being connected to AC power.Was this helpful? Thank you for your feedback!
-
In the Google Home app, go to device settings and set up your home address again. The home address is where the Oasis sets its time zone. If changes are made, it may be necessary to reboot the speaker. Remove and reinsert the power cable to ensure that the changes take effect.
Was this helpful? Thank you for your feedback! -
Connecting a Bluetooth device for your Enchant Soundbar
- Make sure your Enchant soundbar is turned on by pressing the power button
- There are two ways to enter Bluetooth pairing mode on your Enchant soundbar.
- Press the dedicated source button on top of your Enchant soundbar
- Press the source button until you see "Bluetooth" in the front of the Enchant display. Below is the order when using the source button (note that on Enchant 800 there is only 1 HDMI)
- Press the dedicated source button on top of your Enchant soundbar
- The second option is to use the Remote control included with your Enchant soundbar.
- Press the "BT" button on your Remote control.
- The display will show "Bluetooth pairing"
- Now that your Enchant soundbar is in pairing mode it is now time to grab your mobile device.
- Go to Bluetooth settings.
- Press the enable Bluetooth button.
- Select the Enchant soundbar and connect with Bluetooth.
You can now stream any music from your favorite device directly to the Enchant soundbar, ENJOY!
Was this helpful? Thank you for your feedback! - Make sure your Enchant soundbar is turned on by pressing the power button
-
TV Connection HDMI (ARC)
- Connect your HDMI cable (included in the box) to your TV.
- Locate your TVs HDMI ARC (Audio Return Channel) port.
- Find the HDMI OUT on the back of your Enchant 800 or 1300 Soundbar.
- Now enjoy watching TV and listen to great audio through your Enchant soundbar.
Optical connection
- Connect your Optical cable (included in the box) to your TV.
- Find the Optical OUT connection on your TV.
- Locate the Optical IN on the back of your Enchant soundbar.
- Enjoy sound through the optical connection.
Using the HDMI Inputs
- Find an HDMI Cable for your other devices.
- Use the HDMI inputs on the Enchant Soundbar.
- NOTE: Enchant 800 only have one HDMI input port and Enchant 1300 has three HDMI input ports.
- Switch source using your Remote control or pressing the source selector button
.
- The display on your Enchant device will show which HDMI input you are on.
- Enjoy watching or playing through your Enchant Soundbar.
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 11:00-16:00
