Resetting the Go + Play 3 to Factory Settings:

In power ON mode, press and hold the "Volume +" and "Bluetooth" buttons at the same time for more than 10 seconds.

- The Go + Play 3 will power off and back on and is now reset

We offer a 30 day free return period. To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.

In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.

At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.

Download the HK Connect app to your mobile device. Make sure that the Onyx Studio 4 speaker is connected successfully to your mobile device. The HK Connect app should recognize the Onyx Studio 4 within the first few seconds. Once inside the app you can activate the voice assistant and connect to other Connect+ Harman Kardon devices.

Switch device ON.
Press and hold VOLUME+ and PLAY/PAUSE buttons until all lamps light up.
Device is now reset.

Because the Right Ear cup is a touch sensor, you simply have to move your finger from top to bottom on the outside ear cup to increase the volume. In order to decrease the volume, move your finger from the bottom of the ear cup to the top.

With the table stand, Sabre 35 is 125 mm high and 55 mm deep.

For the owner, two indications show the difference: 1. In the menu system, a Spotify option is available as one of the tiles. 2. A check of the software version will show 3.16.0 or higher. There is no mention of the Spotify option on the BDS unit itself. For customer service, a serial number check will show the precise model.

The memory is based on flash memory, and is not forgotten.

If your OMNI 50+ is completely drained, it will take 3,5 to 4 hours to fully charge. We advise to charge the Omni 50+ when it starts to blink red.

AURA Studio has the Multi-Connect feature (Social-Mode) which allows you to connect up to 2 devices at the same time and play different music from either device. Note that the music playing on one device will be interrupted when the other device begins playing music, and vice-versa.

You can have two connectecd devices at the same time.

As a stand-alone soundbar, the product can support 5.0.2 channels. When connected to the optional Citation Sub or Citation Sub-S, the product can support 5.1.2 channels.

It is also possible to have physical rear surround channels by connecting the optional Citation Surround.
 

The amount of Chromecast speakers you can stream music to depends on the bandwidth of your local wireless network. Theoretically, an unlimited amount of devices can be connected to stream the same song.

Our Multi-Connect feature supports up to two devices, to be connected at the same time. But only one device can play at a time.

The Vi Personal Trainer is pre-fitted with the size small fin and comes with two additional fin sizes. To get accurate ratings on your heart rate, you'll want to find the fin that fits most comfortably. The Vi also comes pre-fitted with the size medium ear tip and comes with four additional tip sizes. (XS, S, M, L)

The BDS -75 and -77 models support 2000 files and 10 folder levels on DLNA.

Three devices can be connected to Go + Play BT/Wireless at the same time. You can easily take turns when playing music from 3 connected devices by pressing play on one of them. If you press play on the second of the connected devices, the first one will be interrupted and the second will start playing, and so on. If you want to connect a 4th device, you'll be required to disconnect one of the connected devices first.

The speaker uses 4 x 15W when running on battery. You will hear a slight lower bass performance, compared to being connected to AC power.

In the Google Home app, go to device settings and set up your home address again. The home address is where the Oasis sets its time zone. If changes are made, it may be necessary to reboot the speaker. Remove and reinsert the power cable to ensure that the changes take effect.
 

Connecting a Bluetooth device for your Enchant Soundbar

1. Make sure your Enchant soundbar is turned on by pressing the power button
2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar.
   1. Press the dedicated source button on top of your Enchant soundbar
   2. Press the source button until you see "Bluetooth" in the front of the Enchant display. Below is the order when using the source button (note that on Enchant 800 there is only 1 HDMI)

                  

3. The second option is to use the Remote control included with your Enchant soundbar.
   1. Press the "BT" button on your Remote control.
   2. The display will show "Bluetooth pairing"

                      

4. Now that your Enchant soundbar is in pairing mode it is now time to grab your mobile device.
5. Go to Bluetooth settings.

6. Press the enable Bluetooth button.

7. Select the Enchant soundbar and connect with Bluetooth.

You can now stream any music from your favorite device directly to the Enchant soundbar, ENJOY!
 

TV Connection HDMI (ARC)

 

1. Connect your HDMI cable (included in the box) to your TV.
2. Locate your TVs HDMI ARC (Audio Return Channel) port.
3. Find the HDMI OUT on the back of your Enchant 800 or 1300 Soundbar.
4. Now enjoy watching TV and listen to great audio through your Enchant soundbar.

Optical connection

1. Connect your Optical cable (included in the box) to your TV.
2. Find the Optical OUT connection on your TV.
3. Locate the Optical IN on the back of your Enchant soundbar.
4. Enjoy sound through the optical connection.

Using the HDMI Inputs

1. Find an HDMI Cable for your other devices.
2. Use the HDMI inputs on the Enchant Soundbar.
   1. NOTE: Enchant 800 only have one HDMI input port and Enchant 1300 has three HDMI input ports.
3. Switch source using your Remote control or pressing the source selector button.
4. The display on your Enchant device will show which HDMI input you are on.
5. Enjoy watching or playing through your Enchant Soundbar.

 

Citation One and Citation 100

1. Press the Bluetooth icon. Located on the top panel.
2. Go to -menuMake sure Bluetooth is 
3. Find your Citation speaker and connect.

         

4. You are now connected and ready to play music over Bluetooth, Enjoy!

Citation 300, 500, Bar and Towers

1. Swipe up on the display to find Bluetooth icon.
2. Tap Icon will light up Go to -menu Make sure Bluetooth is
3. Find your Citation speaker.

        

4. You are now connected and ready to play music over Bluetooth, Enjoy!

In our latest update for Citation, we added a couple of new features.
We are going to talk about our new programmable preset feature.

With this feature, you can add a voice command such as "Turn off the lights in the Bedroom" or "Play my playlist Rock road classic" without using your voice.
Once you have recorded the action, you will see an icon on your Citation display. Tap on this specific recorded command, and the Citation will do all the magic for you!

Enough of what it can do, let us create a preset:

1. Scroll down on your Citation Display to you see "Voice presets."
2. Press on the + sign.
3. Say your command: Play Radio FM
   1. Do not use "Hey or OK, Google at this point."
4. Press the "V" icon after the command is finished.
5. Select an icon.
6. Your Preset is now ready, tap it to give it a try.

To delete any presets.

• Press and hold down the preset.
• A menu will appear, hit the "TRASHCAN" icon.

If you have two of the same model Google Assistant speakers, you can create a stereo speaker system.

How to create a stereo pair...

1. Open the Google Home app
2. Find the speaker you want to setup in stereo pair
3. Find the speaker/room
4. Tap on Settings
5. Go to Sound Settings
6. Find the Speaker pair
7. You are now entering the setup page Tap
8. Find your speaker under the Pair with list and tap.
9. Move the speaker to be Left or Right side and press
   1. You can tap on Play sound to identify which speaker it is.
10. Find a name for your Stereo pair
11. It takes a minute to complete the setup.
12. When the configuration is done it will say Ready
13. Press Done

You have now completed the setup and created a Stereo pair sound experience.

NOTE 1:  This is only possible with two of the same speakers.  If they are not identical (Example: Citation 100 & Citation One), setting up a stereo pair will not be an option.

NOTE 2: It is only possible to use Chromecast and Bluetooth in stereo, Airplay will be mono (and should be grouped in iOS Airplay menu.

 

1. Touch the microphone icon on the screen to mute the Google Voice assistant microphone.
   1. NOTE: Google Assistant will not work when the microphone is muted.
2. Touch and press it again to unmute the microphone.
3. You can now give it any voice commands that you would like.

 We strongly recommend that you use the original packaging with the existing shock-absorbing packaging material.

Don’t have the original packaging?

Please follow these important guidelines to ensure that you pack the device safely and avoid shipping damage.
 

• Never use bubble-wrap only.
• Choose a sturdy cardboard box that permits at least 10cm of packaging materials between the device and the walls of the box. Putting the device into a cardboard box without proper shock-absorbing packaging materials will result in damage to the device.
   Air-bubble isolation and foam beans is advisable only for very light-weight items.
• Use packaging materials that cannot move around, and cannot be damaged by the device moving around and being shaken about.

 

How to pair an Enchant Subwoofer with your Enchant bar

1. Go to the back of your Enchant soundbar (800 or 1300)
2. Press the "Subwoofer pairing" button for 2 seconds.

3. In front of your Enchant display, it will say "Subwoofer pairing"
4. Go to the back of your Enchant subwoofer.
5. Press the "Subwoofer pairing" button.

6. The small LED indicator will start to flash rapidly and when the connection is successful, it will be a steady light.

You now have more bass performance and can enjoy deeper richer sound!

1. Power on your Enchant 800 or Enchant 1300 Soundbar. 2. There are two ways to enter Bluetooth pairing mode on your Enchant soundbar. 2.1. Press the dedicated source button on top of your Enchant soundbar source 2.2. Press the source button until you see "Bluetooth" in the front of the Enchant display. 3. The second option is to use the Remote control included with your Enchant soundbar. 4. Press the "BT" button on your Remote control. 5. The display will show "Bluetooth pairing". 6. Go to your Bluetooth settings menu on your mobile device. 7. Enable Bluetooth and connect to your Enchant 800 or Enchant 1300 Soundbar.