How To
How To
437 results
-
For Citation ONE, Citation 100, Citation Sub and Citation Surround, Press and hold the RESET button on the speaker for 5 seconds. For Citation 300, Citation 500, Citation Bar and Citation Tower, Press and hold the RESET button on the speaker for 5 seconds, or select the Factory Reset option in the touch screen settings menu.Was this helpful? Thank you for your feedback!
-
That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".Was this helpful? Thank you for your feedback!
-
We have some suggestions if you want to enjoy the best performance from your Bluetooth devices. 1. Please note that if you have a large number of Apps open in your smartphone or tablet, this may block or overtax its processor. Dropouts may result. Try to close all or most active apps. This should solve the problem. 2. Bluetooth signals from smartphones and tablets are not very strong. Make sure that the signal does not have to pass through doors, walls etc. Always maintain a clear line of sight between transmitter and receiver. 3. Do not carry your smartphone in your pocket, if you have dropouts. Your body can act as a screen, reducing the strength of the Bluetooth signal. Put the phone on a table or other surface. 4. Do not walk around while listening. If the transmitter and the receiver are moved in relation to each other, dropouts occur more frequently. 5. Under normal circumstances, you can expect a range of 5 meters with no problems, if you follow the above advice. In some instances range is longer, but we cannot promise this.Was this helpful? Thank you for your feedback!
-
To prevent other people from changing the source on your BDS through Bluetooth, you can disable the “Automatic Playback” function in the System Settings of the BDS ( 280, 580, 280S and 580S ). This does not prevent others from connecting to one of the two Bluetooth receivers in the BDS units, but it prevents other people from “interrupting” your playback source. This is where the change is done: Settings – System Settings Automatic Playback ( Enable/Disable ) Enabled: People can connect to your BDS and start playing music/audio. Your BDS will automatically change source ( or switch on, when BDS is in Standby mode ) from any source. Disabled: People can connect to your BDS, but the BDS will not automatically change source, or go out of Standby mode when a music/audio signal is sent through Bluetooth.Was this helpful? Thank you for your feedback!
-
Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.Was this helpful? Thank you for your feedback!
-
There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.Was this helpful? Thank you for your feedback!
-
With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.Was this helpful? Thank you for your feedback!
-
To choose a wireless network for your BDS system, please do the following. 1: Select Choose a network from the Setup Wi-Fi list. 2: Follow the instructions on the screen to select your wireless home network and enter your security password, if applicable.Was this helpful? Thank you for your feedback!
-
Download and connect the Onyx Studio 9 with the Harman Kardon One app. Select the product in the app and go to [Product information] and then select [Product Software]. If a new update is available, you can select [Update].
Was this helpful? Thank you for your feedback! -
The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.Was this helpful? Thank you for your feedback!
-
Please refer to the owner's manual for AVR 151 or 151S. The procedure is explained there. The remote control contains a number of pre-programmed command sets that can be activated to control TV sets, disc players and other devices of various brands.Was this helpful? Thank you for your feedback!
-
You can send any 4k video signal into the HDMI inputs of your AVR, and it will be sent to your TV screen from the HDMI output, either in 4k or 1080p. Sometimes it may be necessary to switch off the TV set, then switch it on again, to activate a new "handshake" between the devices, in order to open for the 4k signal, if normal HD 1080p signal was the last signal used. Please note that not all 4k signals can be viewed. Many streamed videos from Youtube will work, as will any 4k material that you have recorded yourself, and many TV boxes will work also. However, HDCP 2.2 protected material will not be shown in 4k, but will be converted to full HD 1080p signals, because these AVRs do not support HDCP 2.2 digital copy protection. HDR is not supported.Was this helpful? Thank you for your feedback!
-
With no signal, the BDS will turn itself off after the number of minutes you have previously set. When connected with optical cable to an external source, and with signal present, it will not turn off, even if the Auto Turn Off is on.Was this helpful? Thank you for your feedback!
-
Each speaker, adaptor and phone/tablet connects to your home Wi-Fi network, just like any other Wi-Fi produce you own. You can then stream any music from your phone/tablet to any Omni speaker or Adapt over your home networkWas this helpful? Thank you for your feedback!
-
Vi measures heart rate using an optical heart rate sensor in the left earbud. The sensor emits light in a specific wavelength to the tissue of the tragus in the ear, and the reflective light is captured by the receiver of the sensor, that is processed by a proprietary algorithm to capture the heart rate. If you need assistance getting an accurate and consistent heart rate, check out this tutorial video to find the correct fit.Was this helpful? Thank you for your feedback!
-
The two subwoofer outputs are parallel, meaning that when changing subwoofer settings in the setup menu, both outputs will be adjusted. Establish the 7.2 system simply by adding a second subwoofer to an existing 7.1 system, connecting it to sub output 2.Was this helpful? Thank you for your feedback!
-
You can change the volume on the Harman Kardon Aura Studio 2 by either using the volume control ( indicated with the + and - ) on the front of the Aura Studio 2. Alternatively, when connected by Bluetooth from a mobile device, you can change the volume from the mobile device. There are 32 steps in the volumeWas this helpful? Thank you for your feedback!
-
Plug in via USB charging port behind the cap on the RIGHT side of your neckband just below the volume controls. When the light is on, your neckband turns green. (Press the plus and minus on the volume control to get the battery status)Was this helpful? Thank you for your feedback!
-
With the SB35 in standby, press and hold Volume plus and Volume Minus for more than three seconds. The software version is now shown on the front panel display, under the fabric grille. It is the first figure that is the software. More info is shown, but is not relevant for user.Was this helpful? Thank you for your feedback!
-
You need to download the HK Alexa setup app from either Google Play Store or Apple App Store, then follow the procedure written in the app.Was this helpful? Thank you for your feedback!
-
We recommend starting playback on the Omni+ speaker first, and then linking the 1st generation Omni speakers. Omni+ is more powerful and can provide more stability when restreaming to other speakers.Was this helpful? Thank you for your feedback!
-
You can download a copy of your invoice on our website. Go to "Order Status" under "Order Support" in the menu bar. To access your order details and download your invoice, you will need the following details:
- Order number
- Surname
- Billing postal code
Once directed to your order details, there is an option to download your invoice.
The details on your invoice is a direct reflection of your order details. We are unable to amend the details on your invoice.Was this helpful? Thank you for your feedback! -
1. Place the 3770 in Bluetooth input mode with the BT button on the front panel or the remote. 2. Do a BT search on the phone, until you find HK3770. Then pair with it. 3. Now you can select the HK3770 as audio source on your phone, depending on the phone. On some phones, you can simply begin to play music after performing the pairing, and the HK3770 will play, if it is in Bluetooth input mode, shown on the front panel display. 4. You can control play/pause etc. from either your phone or from the HK3770 remote control. If you want to use the HK3770 remote, you must first press the STEREO Button on the remote control in order to activate the correct remote codes. Now a press on the PAUSE Button on the HK3770 remote will pause the music by placing your phone on pause, and you can restart play by pressing the PLAY Button. 5. To pair another source to HK3770, first deactivate BT on the source presently paired to release new pairing.Was this helpful? Thank you for your feedback!
-
Make sure that the unit you are attempting to connect to is in pairing mode under Bluetooth Settings. Press the power button located on far right outer rim of the speaker. If this is the first time connecting the unit, it will immediately go into pairing mode. HK Onyx 4 Studio should show up on your discoverable devices within 3-5 seconds. Once you choose the HK Onyx Studio 4 on your device, you will be connected and ready to experience that superior Harman Kardon sound.Was this helpful? Thank you for your feedback!
-
Press and hold the bluetooth button for 2-3 seconds. The bluetooth button is located on the bottom RIGHT ear cup. If this is your first time turning on the headphones, it should immediately begin to search for a device to connect to. You will see the blue LED light flash on the bluetooth symbol as it begins to search for the device. Make sure the bluetooth setting is on and in search mode on your device. The Soho Wireless should appear on your discoverable devices within 3-5 seconds. To power off, press and hold the bluetooth button until you hear the audio music prompt indicating that it has powered down.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Handsfree" ( phone ) button together for 5 seconds. The Harman Kardon Aura Studio will power off, and is now reset back to factory defaults.Was this helpful? Thank you for your feedback!
-
Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 11:00-16:00
