How To
How To
442 results
-
Each speaker, adaptor and phone/tablet connects to your home Wi-Fi network, just like any other Wi-Fi produce you own. You can then stream any music from your phone/tablet to any Omni speaker or Adapt over your home networkWas this helpful? Thank you for your feedback!
-
With no signal, the BDS will turn itself off after the number of minutes you have previously set. When connected with optical cable to an external source, and with signal present, it will not turn off, even if the Auto Turn Off is on.Was this helpful? Thank you for your feedback!
-
You can send any 4k video signal into the HDMI inputs of your AVR, and it will be sent to your TV screen from the HDMI output, either in 4k or 1080p. Sometimes it may be necessary to switch off the TV set, then switch it on again, to activate a new "handshake" between the devices, in order to open for the 4k signal, if normal HD 1080p signal was the last signal used. Please note that not all 4k signals can be viewed. Many streamed videos from Youtube will work, as will any 4k material that you have recorded yourself, and many TV boxes will work also. However, HDCP 2.2 protected material will not be shown in 4k, but will be converted to full HD 1080p signals, because these AVRs do not support HDCP 2.2 digital copy protection. HDR is not supported.Was this helpful? Thank you for your feedback!
-
Please refer to the owner's manual for AVR 151 or 151S. The procedure is explained there. The remote control contains a number of pre-programmed command sets that can be activated to control TV sets, disc players and other devices of various brands.Was this helpful? Thank you for your feedback!
-
The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.Was this helpful? Thank you for your feedback!
-
Download and connect the Onyx Studio 9 with the Harman Kardon One app. Select the product in the app and go to [Product information] and then select [Product Software]. If a new update is available, you can select [Update].
Was this helpful? Thank you for your feedback! -
To choose a wireless network for your BDS system, please do the following. 1: Select Choose a network from the Setup Wi-Fi list. 2: Follow the instructions on the screen to select your wireless home network and enter your security password, if applicable.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.Was this helpful? Thank you for your feedback!
-
With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.Was this helpful? Thank you for your feedback!
-
On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.Was this helpful? Thank you for your feedback!
-
The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 11:00-16:00
