AVR 151

Specifications

Specifikationer

Power requirement: 220V – 240V AC/50Hz – 60Hz

Power consumption: <0.5W (standby); 410W maximum

Weight: 4.6kg (10 lb)

Lydspecifikationer

Frequency range: 87.5MHz –108.0MHz

Signal-to-noise ratio (mono/stereo): 70dB/68dB

Distortion (mono/stereo): 0.2%/0.3%

Stereo separation: 40dB @ 1kHz

Selectivity (±400kHz): 70dB

Denne 375-watt, højeffektive 5.1-kanals A/V-receiver får din musik, dine film og dine tv-serier til at lyde bedre end nogen sinde før. Uanset om det er din Blu-ray™-afspiller, HD-kabel-boks eller spillekonsol, vil du have den bedste billedkvalitet og lyd. Og du har brug for én enkel måde at tilslutte dem alle på. Harman Kardon® AVR 151 er en 5.1-kanals audio/video-receiver med netværk, som har fire 3D-ready HDMI®-indgange med 4K-pass-through – tilslut dem én gang, og du er klar. Med DLNA® 1.5 kan du streame lyd fra dine enheder med netværk, og den integrerede vTuner™-internetradio giver dig forbindelse til en hel verden af online lydunderholdning. AVR 151 er alsidig og muskuløs – den kan udsende op til 375 watt. Med den kan du høre kraftig lyd med al den nøjagtighed, du kender og elsker fra Harman Kardon-produkter. Receiveren er også lettere takket være HARMAN GreenEdge™-certificeringen. Du vil opleve sand styrke – bare i en mere miljøvenlig formfaktor. Og hvis du er en af dem, der gerne vil have mere kontrol, kan du hente Harman Kardon Remote-app'en. Den giver dig friheden til at styre din hjemmebiografoplevelse fra din egen velkendte enhed. Elegant, let og kraftig – Harman Kardon AVR 151 er den perfekte balance mellem alsidighed og smuk lyd.

Fem forstærkere med 75 watt pr. kanal og højeffektiv digital strømforsyning

Den højeffektive AVR 151-audio/video-receiver sender 75 watt pr. kanal ud for at drive et fuldt 5.1-kanals surroundsoundsystem. Den kan også tilsluttes aktive subwoofere og give forbedret lavfrekvent ydeevne til din musik, dine film, HDTV-serier, sportsudsendelser og videospil. Mens forstærkeren bevarer det velkendte Harman Kardon HCC (high-current capacity), ultrabred båndbredde-forstærkerdesign for at sikre den mest nøjagtige, dynamiske lyd med forbedret klarhed og realisme selv ved de højeste lytteniveauer, giver en digitalt baseret strømforsyning forstærkerne hele den styrke, de skal bruge – uden vægten fra traditionelle strømforsyningsdesign og deres tunge transformere. Slutresultatet er et produkt, der lyder fremragende, i en mindre formfaktor, som er miljøvenlig./p>

DLNA 1.5-netværkstilslutningsmulighed

AVR 151 er DLNA 1.5-kompatibel, hvilket giver dig mulighed for at levere lyd over dit hjemmenetværk via kompatible enheder som f.eks. smartphones, tabletter og computere.

Indbygget vTuner-internetradio

AVR 151 har vTuner-internetradio, så du har forbindelse til en hel verden af online lydunderholdning. Så snart den er pakket ud, kan du streame ”over-the-air”-radiostationer fra hele verden samt streame fra en lang række radiostationer, der kun findes på internettet.

Fire 3D-ready HDMI-indgange

Fire HDMI-indgange med 3D og 30/36-bit Deep Color leverer digital HD-video i opløsninger op til 1080p med lyd i fremragende gengivelseskvalitet gennem et enkelt kabel. Der er intet kvalitetstab for billeder eller lyd pga. konvertering, men bare den Hollywood-spænding som skaberne ville have dig til at opleve.

USB-port på frontpanelet til tilslutning af Apple-produkter eller USB-stik/h3>

AVR 151 giver dig mange muligheder for lydafspilning med USB-porten på frontpanelet. Tilslut blot en iPhone, iPad eller et USB-stik, og afspil dine gemte numre via dit hjemmeunderholdningssystem. Den integrerede USB-port oplader også dine iOS-enheder.

Dolby TrueHD- og DTS-HD Master Audio-afkodning

AVR 151 leverer lyd i høj opløsning, som svarer til den digitale billedkvalitet på Blu-ray Disc™-formater, så du kan nyde det fulde potentiale i filmsoundtracks formateret med Dolby® TrueHD- og DTS-HD Master Audio™-kode. Uanset hvilken tilstand eller hvilket humør du er i, hører du altid lydafspilning i den bedste kvalitet.

FAQs & How-Tos

14 results

Sort

Page size

Can AVR 151 and 151S do 4K upscaling?

No, 4K upscaling is not possible. It was mentioned in the specification sheet and on the web page that this feature was supported, but that is an error.

Was this helpful? Thank you for your feedback!
Can I choose between sound from my TV or sound from the AVR?

Yes, in the HDMI Setup Menu, it is possible to select either �Sound To TV� or �Sound To Amp�, Amp being the AVR. This detail is not mentioned in the owner's manual.

Was this helpful? Thank you for your feedback!
I have connected my computer / NAS drive to my router, as well as to my AVR. But when I switch the computer / NAS drive ON, the AVR loses its connections, deactivating the Remote App as well as internet radio.

This is sometimes a problem with wired connections to computers or NAS drives. There is no way to change this, unfortunately.

Was this helpful? Thank you for your feedback!
I have downloaded the Harman AVR App, but it does not work when I open it and try to control my receiver. What can I do?

The Harman AVR App controls your receiver through your smartphone, which communicates via your wireless home network. Please make sure that your AVR is properly connected to your network router, with cable for the smaller models. If you have no wireless home network, you cannot use the app.

Was this helpful? Thank you for your feedback!
Is it possible to change the name of a receiver with internet connection?

Yes, on your computer, enter the IP address of the receiver in the internet browser. In the page that opens, it is possible to change the name.

Was this helpful? Thank you for your feedback!
Is it sufficient to put the AVR into standby, before connecting a Source or a TV?

For your personal safety and to avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the AVR and ALL source equipment from the AC output before making any audio or video system connections.

Was this helpful? Thank you for your feedback!
My AVR/BDS/HK shows the word "Protection" in the display window, and will not work. What can I do to find out if it is defective, or if there are other problems?

There are five possible reasons for the receiver shutting down. 1. There is a problem internally with the receiver. 2. There is a problem with one or more of your speakers. 3. There is a problem with one or more of your speaker wires. 4. There is a problem with the speaker wiring done on your system. 5. The unit is overheating. No ventilation. First, check the wiring at every speaker terminal at the back of your receiver and at the back of your speakers. A single strand of speaker wire crossing from one terminal to another would be enough to cause the amp to shut down or go into PROTECT. If you do not find any problems with any of the wiring, you should disconnect all speakers from your receiver. If the receiver continues to go into PROTECT, the problem is in the receiver. Please submit a case on the Contact Us page. They will be able to assist you. However, if it turns on, the problem is elsewhere. Begin reconnecting one speaker at a time. Eventually you will connect a speaker that will cause the receiver to shut down. At this point you have found your culprit. On the other hand, it may just be overheating. You must have at least 2 - 3 inches of space between the top of the unit and any shelf or component above the unit. The unit should not be inside a sealed compartment when being used. The unit must be able to breath. There are very powerful amps in these receivers. If they run too hot, they will shut down. An external fan can help this.

Was this helpful? Thank you for your feedback!
My AVR is shutting down when my TV is turn off. What is causing this?

If you have enabled HDMI-link (CEC function), then you will experience that your AVR will do some actions based on the CEC function coming from your TV, which in this case it will follow your TV when it goes into standby.

Was this helpful? Thank you for your feedback!
My receiver does not show "DTS HD Master Audio" in the display, even though the Blu-ray disc should have this format. Instead, it just shows "DTS".

With some Blu-ray discs, you have to go to the Settings Menu of your Blu-ray player and select "Bitstream" or "Bitstream Native". This will carry the DTS HD Master signal to be decoded in the AVR, and the AVR front panel should show the correct text.

Was this helpful? Thank you for your feedback!
My receiver makes a clicking sound when I adjust the volume. Is this normal?

Yes, this is a normal characteristic of this system.

Was this helpful? Thank you for your feedback!