AVR 7300
Audio/Video Receiver With Dolby Digital & DTS (125 watts x 2 | 110 watts x 7)
Vendido desde 2004 hasta 2006
| Producto predecesor: | AVR 7200 |
|---|---|
| Hecho en: | China |
Documentos y descargas
Especificaciones del producto
- Power Requirements
- 120V AC/60Hz
- Power Consumption
- 8.9W Standby 130W Idle, 1,360W Max. (7 channels driven)
- Digital Inputs (coaxial/optical)
- 3/3 on Rear; 1 (switchable to output)/1 on front
- Analog Inputs
- 1 A/V on front panel (switchable to output)
- Analog Inputs
- 2 audio-only
- Analog Inputs
- 5 A/V on rear panel
- Analog Inputs
- 6-/8-channel input
- Analog Inputs
- tuner
- On-Screen Display
- Yes
- Multizone Capability
- Audio and video; A-BUS Ready (two jacks); RS-232 serial control port; surround back channels assignable to remote zone; Zone II remote
- Auto Setup
- EzSet remote
- Remote Control
- Backlit, eight-device, programmable learning remote (2-line LCD display)
- Shipping Weight (System, Accessories, Packing)
- 69.3 lb (31.5kg)
- MSRP U.S.
- $2399.95 each
- # of Amplifier Channels
- 7
- Continuous Average Power (FTC) per Channel (stereo mode)
- 125 Watts per channel @ <0.07% THD, 20Hz – 20kHz, both channels driven into 8 ohms
- Front L & R Channels
- 110 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Center Channel
- 110 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Surround Channels (L & R Side, L & R Back)
- 110 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
- Input Level/Impedance
- 200mV/47k ohms - Linear (High-Level)
- Signal-to-Noise Ratio
- 100dB (IHF-A)
- Frequency Response
- 10Hz – 100kHz (+0/-3dB @ 1 watt)
- Surround System Adjacent Channel Separation:
- Dolby Pro Logic I/II/IIx
- 40dB
- Dolby Digital
- 55dB
- DTS
- 55dB
- Transient Intermodulation Distortion (TIM)
- Unmeasurable
- Slew Rate
- 40V/µSec
- Width
- 17.3 inch (440mm)
- Height
- 7.6 inch (192mm)
- Depth
- 2.5 inch (520mm)
- Weight
- 55 lb (24.9kg)
- Dimensions:
- Carton Dimensions
- 23 inch (583mm) x 12.7 inch (323mm) x 24.7 inch (626mm)
- Television Format
- NTSC
- Input Level/Impedance
- 1Vp-p/75 ohms
- Output Level/Impedance
- 1V/75 ohms
- Composite and S-Video
- 10Hz – 8MHz (–3dB)
- Component Video
- 10Hz – 100MHz (–3dB)
- Frequency Range
- AM... 520 – 1710kHz
- Frequency Range
- FM... 87.5 – 108.0MHz
- Signal-to-Noise Ratio
- AM... 45dB
- Usable Sensitivity
- FM... IHF 1.3µV/13.2dBf
- Signal-to-Noise Ratio
- FM... Mono/Stereo 70dB/68dB
- Usable Sensitivity
- AM... Loop 500µV
- Distortion
- AM... 1kHz, 50% Mod. 0.8%
- Distortion
- FM... Mono/Stereo 0.2%/0.3%
- Selectivity
- AM... ± 10kHz, 30dB
- Stereo Separation
- FM... 40dB @ 1kHz
- Selectivity
- FM... ± 400kHz, 70dB
- Image Rejection
- FM... 80dB
- IF Rejection
- FM... 90dB
- Amplifier Power (RMS)
- 110 x 7 @ 8 ohms (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
- High Instantaneous Current Capability (HCC)
- ± 75 Amps
The video part of inchaudio/video receiver inch has never meant so much. In addition to a powerful high-current, ultrawide-bandwidth amplifier and all the audio formats and features you expect from Harman Kardon, the AVR 7300 is equipped with DCDi by Faroudja, image processing which upconverts all inputs to high-resolution component video. Along with built-in test signals and a wide range of video adjustments, the AVR 7300 gives you picture quality to match the unparalleled power and performance of Harman Kardon audio.
Imágenes y vídeos
