AVR 645

AVR 645

Audio/Video Receiver With Dolby Digital, DTS & HDMI 1.1 Switching (90 watts x 2 | 75 watts x 7)

Vendido desde 2006 hasta 2007

Producto sucesor: AVR 3550HD
Hecho en: China

Documentos y descargas

Especificaciones del producto

Power Requirements
AC 120V/60Hz
Power Consumption
120W @ Power On, idle; 1272W @ rated power output (7 channels driven)
Digital Inputs (coaxial/optical)
3/3 on Rear; 1 (switchable to output)/1 on front; 1 USB on rear
Analog Inputs
1 A/V on front panel (switchable to output)
Analog Inputs
2 audio- only
Analog Inputs
4 A/V on rear panel
Analog Inputs
6-/8-channel input
Analog Inputs
The Bridge Digital Media Player
Analog Inputs
tuner
On-Screen Display
Yes, including component video
Multizone Capability
Audio; A-BUS Ready; RS-232 serial control port; surround back channels assignable to remote zone; ZR 10 remote
Auto Setup
EzSet/EQ room equalization
Remote Control
Backlit, eight-device, programmable learning remote (2-line LCD display)
Shipping Weight (System, Accessories, Packing)
47 lb (21.4kg)
MSRP U.S.
$1499.95 each
# of Amplifier Channels
7
Continuous Average Power (FTC) per Channel (stereo mode)
90 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms
Front L & R Channels
75 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Center Channel
75 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Surround Channels (L & R Side, L & R Back)
75 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms
Input Level/Impedance
200mV/47k ohms - Linear (High-Level)
Signal-to-Noise Ratio
100dB (IHF-A)
Surround System Adjacent Channel Separation:
Dolby Pro Logic I and II
40dB
Dolby Digital
55dB
DTS
55dB
Frequency Response
10Hz – 130kHz (+0/-3dB @ 1 watt)
Transient Intermodulation Distortion (TIM)
Unmeasurable
Slew Rate
40V/µsec
Width
17.3 inch (440mm)
Height
6.5 inch (165mm)
Depth
17.1 inch (435mm)
Weight
41 lb (18.6kg)
Dimensions:
Carton Dimensions
20.1 inch x 10 inch x 22.2 inch (510mm x 254mm x 565mm)
Television Format
NTSC
Input Level/Impedance
1Vp-p/75 ohms
Output Level/Impedance
1V/75 ohms
Video Frequency Response:
Composite and S-Video
10Hz – 8MHz (–3dB)
Component Video
10Hz – 100MHz (–3dB)
HDMI
Version 1.1 with audio processing
Frequency Range
AM... 520–1720kHz
Frequency Range
FM... 87.5 – 108.0MHz
Signal-to-Noise Ratio
AM... 45dB
Usable Sensitivity
FM... IHF 1.3µV/13.2dBf
Signal-to-Noise Ratio
FM... Mono/Stereo 70dB/68dB
Usable Sensitivity
AM... Loop 500µV
Distortion
AM... 1kHz, 50% Mod 0.8%
Distortion
FM... Mono/Stereo 0.2%/0.3%
Selectivity
AM... ± 10kHz, 30dB
Stereo Separation
FM... 40dB @ 1kHz
Selectivity
FM... ± 400kHz, 70dB
Image Rejection
FM... 80dB
IF Rejection
FM... 90dB
Amplifier Power (RMS)
75 x 7 @ 8 ohms, (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)
High Instantaneous Current Capability (HCC)
± 50 Amps

Versatility at its best! The AVR 645 not only switches two HDMI; 1.1 sources, it is able to decode Dolby Digital, DTS and PCM audio streams from the HDMI inputs. Add USB audio, iPod connectivity and XM-Ready capability to our EzSet/EQ system and high-current amplifier, and the AVR 645 performs with ease. Equally impressive on the video side is transcoding so that all analog video inputs may be viewed via component outputs, and A/V Sync Delay, which reconnects the timing of sound and images. There is no better combination of sound and image anywhere.

¿No encuentras lo que buscas?

Envíanos un correo electrónico

Envíanos un correo electrónico

los 365 días del año.

Envíanos un correo electrónico